Currently Browsing: Tutorials

CK3 Probe II Tutorial – MRA MODE (Liteon 83850V2 & 93450)

CK3 Probe II Tutorial – MRA MODE (Liteon 83850V2 & 93450) Instructions Here is the method to do a full dump of your Liteon drive using the CK3 Probe II (MRA) Method. This has been tested working on ALL drives including  83850 v2 & 93450 (it works on the older 74850, 83850 v1 but there is no need to do an MRA dump of those drives – it's already proven that the laser calibration data was just manufacturer data and does not have any bearing on the fw at all) – including BOTH the MXIC & WINBOND chipsets (Some competitors products do not have the Probe v1 function, do not have the Multi-R switch and do not have circuit protection – so be aware of the differences before you purchase.) Recommended Tools (Sponsored by ModTraders) CK3 Pro: http://www.modtraders.co.uk/xecuter-ck3pro-rev-d.html CK3 Probe II: http://www.modtraders.co.uk/xecuter-ck3-probe-v2.html Fiberglass Scratch pen: http://www.modtraders.co.uk/xecuter-fiberglass-scratch-pen.html Xacto Knive Set: http://www.modtraders.co.uk/16pc-xacto-style-knive-set.html Before you use the CK3 Probe II we recommend that you make sure your PC SATA setup is working correctly. So connect the CK3 Pro to the DVD drive and connect the SATA cable to your SATA card/motherboard and check Jungle Flasher to see if there is any communication. If all is well this is what it should look like: We are assuming that you have opened up your Liteon DVD drive and taken the PCB out ready for the procedure. 1. This is how you connect the CK3 Probe II to the CK3 Pro. Make sure the OP Switch is in the UP position and switch the mode to MRA. If you power on the CK3 Pro you will see that the CK3 Probe II BLUE POWER LED is on and the MRA GREEN NORMAL LED is on (IF the RED LED is Lit, OP-Switch is in WRONG position!). This shows that everything is functioning. You should now turn the CK3 Pro power OFF. MULTI-R SWITCH: We recommend you...
Read More of CK3 Probe II Tutorial – MRA MODE (Liteon 83850V2 & 93450)

Tutorials Forum

The support forums have many tutorials that are regularly updated – you need to be registered there to make any posts however you don't have to be registered to read. If you have any questions you wish to post include as much detail as possible and make sure you read the tutorial thoroughly beforehand....
Read More of Tutorials Forum

How To Install The Xecuter RROD Repair Kit Pro II

How To Install The RROD Pro Repair Kit II This tutorial was written by Team Xecuter. If you use anything from this tutorial please give credits and also a direct link to this page. Also if we have made any mistakes or left anything out please let us know – thanks ! Work Time: 20 Minutes Difficulty: Easy Tools Required: Xecuter Unlock Tool & Xecuter RROD Pro Repair Kit (Comes complete with Torx 10 & Torx 8 Screwdrivers, Allen Key, 8 Precision Designed Bolts, 8 Precision Cut Metal Washers, 8 Precision Cut Nylon Washers, 4 Thermal K-Pads & Hi-Quality Thermal Paste) We also recommend that you get yourself some Arcticlean Thermal Grease Cleaning Kit – On Sale Here Only $8.95 for 60ml First follow the guide for disassembling the Xbox 360 case and removing the motherboard. 1. Turn the motherboard over – this will be your work area [Pic 1a] What you are going to do first is remove the 2 large X-Clamps from the motherboard and replace with bolts that have been custom made for a precision fit on the Xbox. [Pic 1] 2. Removing the X-Clamps is pretty easy using long nose pliers or a screwdriver. (Don't use one of the included Torx screwdrivers as you will strip the end). After all 4 corners have been loosened simply remove. Be careful not to touch the motherboard as you can damage the traces. Here is a Video to show how to remove the Xclamps – thanks to Carwilej on Youtube [youtube dDAW_tRiGTU nolink] 3. Now remove the GPU and CPU heatsinks from the motherboard [Pic 3a]. You will see the GPU and CPU exposed and will probably be quite dirty with old thermal grease [Pic 3b]. The best way to clean these is by using original Arcticlean Thermal Grease Cleaning Kit (On Sale Here) [Pic 3a] [Pic 3b]...
Read More of How To Install The Xecuter RROD Repair Kit Pro II

Jungle Flasher Tutorial For Liteon 74850C

The complete guide is posted and maintained on the forums:...
Read More of Jungle Flasher Tutorial For Liteon 74850C

How To Identify & Probe The Liteon 74850C DVD Drive

We have put together this very easy to follow image on how to identify a Liteon 74850C DVD Drive and how to take off the back plate and find the area where you will need to use the CK3 Probe in order to extract the DVD key using Jungle...
Read More of How To Identify & Probe The Liteon 74850C DVD Drive

How to install the Blaster CK3

This tutorial was written by Team Xecuter. If you use anything from this tutorial please give credits and also a direct link to this page. Also if we have made any mistakes or left anything out please let us know – thanks ! The official forum for this tutorial is www.team-xecuter.com/forums/forumdisplay.php?f=104 How to install the new Xecuter Blaster CK3 Install Time: 10 Minutes Difficulty: Easy Tools Required: All tools are included in the package (Unlock Tool, Torx 10 Screwdriver) What's In The Box? Blaster CK3 External Module SATA Cable L Shape Connector SATA Cable Straight Connector Xbox Case Unlock Tool Torx 10 Screwdriver USB Cable (For Liteon 74850C Only) RS232 Serial Cable (For Liteon 74850C Only) Motherboard to DVD Cable SATA Exchange Unit Cable Connects to Blaster CK3 External Module SATA Exchange Unit Blaster CK3 Probe (Liteon 74850C Only) Step By Step Installation Tutorial 1. First, you need to take your Xbox 360 apart. If you don't know how to do this, read this guide. Once you have it taken apart disconnect the cables to the backside of the DVD and set it aside for the time being. Once you have removed the DVD you will see two cables plugged into the Xbox 360 motherboard. One is a Sata cable and one is the DVD power cable (this is the multi wired cable with a white adapter on the end). Remove both cables, you won't be needing those any more. 2. First install the Sata Exchange Unit (#10) to the metal case of the Xbox. You will notice that each connector is color coordinated to make installation as simple as possible. Peel the off the paper to expose the sticky foam insulated pad and attach to the metal case. 3. Now take the Motherboard to DVD Cable  (#8) and plug the white connector to motherboard, then you will see...
Read More of How to install the Blaster CK3

How To Disassemble the Xbox 360 Case

How To Disassemble the Xbox 360 Case Disassemble Time: 5 Minutes Difficulty: Easy Tools Required: Xecuter Unlock KitV2 (Torx 10 Screwdriver Included) If you wish to remove the motherboard to do an RROD repair then you will need to follow Part #2 of this tutorial and also an Xecuter RROD Repair Kit...
Read More of How To Disassemble the Xbox 360 Case