PDA

View Full Version : [Guide] Reading Corona v2 nand with a Micro SD adaptor



Pacote
4th September 12, 15:40
Hope you enjoy the easy to follow pic ;)

http://i.imgur.com/VeWvR.jpg

You can use your internal sd slot reader, or any usb adaptor (for what i heard from Edson, using a internal reader is the best way so far... lots of problem with random low quality usb readers)

48mb read in only 10 secs!!!!



C yall

BL4K3Y
4th September 12, 15:43
Thanks for this, Pacote!

Goldensavage
4th September 12, 15:48
48mb in 10 seconds.... WOW...

Thanks for the share

n1ght0wl
4th September 12, 15:55
interesting :)

snake007
4th September 12, 16:30
Cheers for the guide will be very helpful

metalfan
4th September 12, 20:18
Thanks, easy enough to follow

oO Elite Oo
4th September 12, 20:23
I wont be doing this method since J-Runner being upgraded but nice diagram ;)

Pacote
4th September 12, 20:24
I wont be doing this method since J-Runner being upgraded but nice diagram ;)

J-runner update will fully support this method :)

rdubbs007
6th September 12, 22:55
oh lookie

http://i.imgur.com/Jztmx.jpg

Pacote
9th September 12, 20:44
For those wanting a 100%-will-work reader this is the cheapest

http://dx.com/p/micro-sd-tf-card-reader-max-16gb-30085?item=1

Oggy
9th September 12, 20:50
Too expensive.

2615863
9th September 12, 21:06
Too expensive.

Compare it to a Jrunner V2 ;)

Oggy
9th September 12, 21:38
A JRP 2?

Free?

ppkpatrick
9th September 12, 21:42
My kind of Tutorial,simple yet effective ;)

jimlfixit
10th September 12, 19:15
Sd/ mmc card reader from discount uk 0.99
68 ohm resistor from maplin 0.29 code M68R
Ethernet cable from poundland or discount uk 1.00
Total cost 2.28
and it works flawlessly

edit. pic quality is shite on my iphone 3g sorry lol

blazek566
19th September 12, 19:23
Would this work with demon? thanks:D

Pacote
5th October 12, 16:15
Working fine and no need to desolder the pads to boot xell :D Just disconnect the SD

http://i.imgur.com/sJTTf.jpg
http://i.imgur.com/vAA4b.jpg

seanr28
8th October 12, 11:03
forget it, I see it now:)

GSIBOY
8th October 12, 13:01
For those wanting a 100%-will-work reader this is the cheapest

http://dx.com/p/micro-sd-tf-card-reader-max-16gb-30085?item=1

Do you have any other links? for good micro sd readers

really_wacky
10th October 12, 08:19
Hi guys,

The PDF posted by ZacKwaRRior says to use "*Agw26-28 wire, (do not use kynar!)" But on the picture you posted it looks like kynar but i could be wrong. Is this something to worry about?

When i followed your tutorial i got the Nand to show up in Jrunner but it was 0mb so i desoldered everything. I think the wires where connected wrong because i was confussed that there where 9 pads on the SD but only 8 pins to the micro SD. So i followed the tutorial below and soldered it directly to the Adaptor and checked the wires like 10 times but its not recouldnised :S I also connected pin 1 of the main xbox 360 resonator to ground.

http://img855.imageshack.us/img855/9476/39940883.jpg

Maybe i should just wait for the TX kit, just sucks it allways cost more to ship something to Belgium then the product itself. :p

frostbyt
10th October 12, 23:04
Had the same problem as well..First tried to wire it to the micro sd adapter, then I took the sd reader right out of my pc and wired it in directly...Pc doesn't find anything so I"m assuming the card reader won't work for this...Waiting on 2 more to come in the mail and the tx kit as well :)

Honetrooper
15th October 12, 20:00
Do you bridge points 4 and 6 on the board and use only one wire or do you use 2 different wires and connect then just connect them to the same point in the actual card?

playingmax
17th October 12, 05:02
Do you bridge points 4 and 6 on the board and use only one wire or do you use 2 different wires and connect then just connect them to the same point in the actual card?
on the card reader u bridge 3 and 6. and on the console u only solder to 4 or 6 not both.

2615863
19th October 12, 04:05
would 70 OHM (7 X 10) resistor work?

playingmax
19th October 12, 06:16
yes it would. Im using 2 33ohm n it works perfect.

2615863
19th October 12, 16:50
yes it would. Im using 2 33ohm n it works perfect.

Sweet Thanks!!

siren215
31st October 12, 06:49
Why separate wire connected to crystal as i see in some pics?

smoothtum
16th November 13, 19:56
Hey guys whats the problem my xbox 360 slim wont starthttp://cdncache-a.akamaihd.net/items/it/img/arrow-10x10.png (http://team-xecuter.com/forums/#)


Hey guys sorry my bad english my problem is

i make x360pro v5-2 my xbox slim corona then i make own sd card reader read nand
and suddenly my xbox 360 wont starthttp://cdncache-a.akamaihd.net/items/it/img/arrow-10x10.png (http://team-xecuter.com/forums/#)
nothin happenhttp://cdncache-a.akamaihd.net/items/it/img/arrow-10x10.png (http://team-xecuter.com/forums/#) power adabter is it orange
please help thanks

Joo C
16th November 13, 20:05
Start a new thread, post pics and do you know that TX offers you the convenience of a RW Kit?

franchiz3
24th November 13, 16:35
oh lookie

http://i.imgur.com/Jztmx.jpg
I wired mine like this and I get 0b