HOW and WHY to Solder Correctly

**Xecuter** · 23rd April 10

If you are a novice to soldering WATCH THIS VIDEO !!!!!

It explains how to solder correctly and why. I GUARANTEE this video will change your electronics life - you will not only know how to solder correctly but you will see how EASY it is when you do it correctly.

[ame]http://www.youtube.com/watch?v=I_NU2ruzyc4[/ame]

**BGAMods** · 23rd April 10

i watched that a couple of weeks ago but thanks for posting it, its a real good vid that shows exactly what to do.

**Cadibiagio** · 23rd April 10

i watched it a while ago to, its a realllly good vid

**sick360mods** · 24th April 10

i never was good at soldering but that vid deffinitly will help the next time i have to solder something.

**MasterCyc** · 1st July 10

done a solder course many years ago
great video that good to show others how not to do it 1st and then how to
many people that think about soldering always panic and hold the solder tip on the wire to long and wonder why it sticks to it.
my tips for soldering
Watts 15-30 max
FLux
Small tips very essential in soldering onto mobys
Lead free solder
and not to be scared of doing it get an old pc moby few wires and practice once you get the nack you never look back

**JOCKz** · 2nd July 10

why lead free solder ? Sure its RoHS safe but such little exposure to "lead" solder will not kill you !!! Lead free solder flows at much higher temps so advising novice users to use it will most likely cause them to lift pads, especially if they are not using temperature controlled soldering stations.

**MasterCyc** · 2nd July 10

as stated in my post tips ie my tips you dont have to use lead free solder its just how i learnt many years ago to do it
every person who solders have there way and toolz to do it its just me stating what i wud do
since this is my prefrence
its not a guide to soldering that i posted

**urakh** · 28th September 10

Wow, that was great! -Urakh

**UpHanleyDuck** · 12th October 10

Good soldering tips, however using the QSB's that come with the nand x leave no margin for error, you end up stripping the board of its solder points if you are not precise with your technique.I got through 4 jtag (kit 8's for xenon) before finally getting the method right. Blobbing the solder on the tip and applying it to the QSB + contact on the M board with plenty of flux worked ok for me.Maybe someone with more skill than me should post a video on good QSB soldering methods as i struggled and i imagine many others did with these delicate QSB's

**allisd00m** · 4th October 11

Originally Posted by UpHanleyDuck

Good soldering tips, however using the QSB's that come with the nand x leave no margin for error, you end up stripping the board of its solder points if you are not precise with your technique.I got through 4 jtag (kit 8's for xenon) before finally getting the method right. Blobbing the solder on the tip and applying it to the QSB + contact on the M board with plenty of flux worked ok for me.Maybe someone with more skill than me should post a video on good QSB soldering methods as i struggled and i imagine many others did with these delicate QSB's

Damn, after finally getting hold of a Nand X that's not what I wanted to hear lol.

**marshamods** · 20th October 10

They are only delicate if you are applying your iron on for long amount of times or are using your iron at a very high wattage.

**UpHanleyDuck** · 20th October 10

Originally Posted by marshamods

They are only delicate if you are applying your iron on for long amount of times or are using your iron at a very high wattage.

I was brief with the amount of time the iron was in contact, however you have a point with the wattage of my soldering iron 30W oopps, still learning.....but I still think you need a good technique to get it just right.

**marshamods** · 20th October 10

Originally Posted by UpHanleyDuck

I was brief with the amount of time the iron was in contact, however you have a point with the wattage of my soldering iron 30W oopps, still learning.....but I still think you need a good technique to get it just right.

I use an adjustable iron and set it at about 30w and it works great. Though I have years of experience.

**turkishman** · 13th January 11

that was a pretty informative video i do say.

my first go with a soldering iron was on a rol board swaping out the led's

it more tinning then anything
but man were those leds small

**lordcast** · 22nd December 12

so this is the secret

thanks will try it

**sick360mods** · 20th October 10

its pretty easy after doing a few just use a 15w soldeering iron

**Ginjasy** · 13th January 11

I use an 18w Antex Iron. It's a good iron. Not silly expensive but not crappy cheap. They also have a really wide selection of tips. I like my 0.2mm tip, great for LEDs.

**turkishman** · 13th January 11

meh...
i got a 15-30watt big fat tip
an i use rosin core lead based

i would like a smaller tip but the ol fatty works well enough
for me any way

**he-man** · 2nd September 11

Why did I not see this any sooner....

Thanks, it'll improve my skills for sure!

**anti087** · 4th September 11

Man did this improve my skill im not as worried now doing the reset glitch on my slim now

Similar Threads

HOW and WHY to Solder Correctly

HOW and WHY to Solder Correctly

all solder done correctly, but still frage

im going to solder new switches to the switch board where do i solder?

X3 Won't Run Correctly! HELP

Thread: HOW and WHY to Solder Correctly

Thread Tools

Display

Hybrid View