Similar Threads

  1. Nand-X/nandpro dump problems
    By gangrel_1313 in forum Xecuter NAND-X Support
    Replies: 43
    Last Post: 16th June 12, 22:27
  2. Problems with nandx dying after using NandPro 3
    By VitalPros in forum Xecuter NAND-X Support
    Replies: 2
    Last Post: 4th December 11, 17:27
  3. Win7 x64 CK3 Pro Driver 1.2.25 issues
    By molsen in forum Xecuter CK3 Pro / CK3 Lite
    Replies: 17
    Last Post: 14th September 10, 16:47
  4. virtual xp for /win7
    By raptor700 in forum The Noob Room
    Replies: 1
    Last Post: 18th July 10, 13:06
Results 1 to 9 of 9
  1. #1

    Join Date
    Jul 2009
    Posts
    306
    Skill Level
    faggibjnyg\
    Thanks
    21
    Thanked 11 Times in 11 Posts

    NandPro v3 on win7 x64 Problems

    Does anyone have the NandPro fully working on there win 7 x64 machine? I'm googling frantically and tried updating the dlportio.dll into the nandpro folder, but I still get errors when trying to install the port95nt file.

    So I have tried adding the dll and I have tried running both files in Win xp Pro compatibility mode and I'm still getting the "Unsuppported 16 bit application" error followed by "Unable to Execute"

    The Following User Says Thank You to MOCAMBO For This Useful Post:



  2. #2
    Senior Member
    Join Date
    Nov 2010
    Location
    Scotland
    Posts
    132
    Skill Level
    Getting there
    Thanks
    192
    Thanked 37 Times in 27 Posts

    Re: NandPro v3 on win7 x64 Problems

    I haven't got my coolrunner etc, to perform the RGH yet,but in ubers tut to update the nandx,it says that you have to open the arm v3 hex in flash magic.The hex is in the nandpro 3 folder.I dont think you actually have to run the port95nt app within nandpro 3. I have to admit I tried to install nandpro 3 on my windows 7 64bit,after reading your post,but it wouldn't, no matter what I tried.However I was able to run Flash Magic and place the arm v3 hex from the nandpro folder into flash magic,just for test purposes. So I have no doubt that if my nandx was connected as per the instructions in the tut I would be able to update it.If I am wrong please feel free to correct me(Without facepalms please)

    The Following User Says Thank You to tonyg243 For This Useful Post:



  3. #3

    Join Date
    Jun 2011
    Location
    DUBLIN
    Posts
    597
    Skill Level
    Demon, Rgh, Case Mods, Repairs
    Thanks
    111
    Thanked 110 Times in 93 Posts

    Re: NandPro v3 on win7 x64 Problems

    why are you trying to install the port95nt file. you dont need it i am using win 7 64 bit and i did not go near that file. i finally just programmed my cr with nand pro 3 and dump my nand 3 times with nand pro 3. gonna leave the rest until tomorrow. have all the wiring done also so hopefully i get it all up and running tomorrow

    The Following User Says Thank You to MANUMAN For This Useful Post:



  4. #4

    Join Date
    Jun 2005
    Location
    Netherlands
    Posts
    171
    Skill Level
    softmod, soldered chips, repair
    Thanks
    28
    Thanked 116 Times in 62 Posts

    Re: NandPro v3 on win7 x64 Problems

    put this one in the folder, and try again
    Attached Files Attached Files

    The Following 5 Users Say Thank You to cypher21 For This Useful Post:



  5. #5

    Join Date
    Feb 2003
    Location
    California, USA
    Posts
    6,212
    Skill Level
    Modding, Gaming
    Thanks
    1,151
    Thanked 19,102 Times in 2,698 Posts

    Re: NandPro v3 on win7 x64 Problems

    and make sure you have the x64 win 7 signed drivers for nandx installed - NOT the ones that come with nandpro3
    PLEASE READ THE FORUM RULES BEFORE POSTING HERE

    The Following User Says Thank You to Ubergeek For This Useful Post:



  6. #6
    Junior Member
    Join Date
    Apr 2005
    Location
    UK
    Posts
    15
    Skill Level
    Coding
    Thanks
    3
    Thanked 6 Times in 5 Posts

    Re: NandPro v3 on win7 x64 Problems

    that DLPortIO fixed it for me, thanks

    The Following User Says Thank You to hydrasworld For This Useful Post:



  7. #7
    Senior Member
    Join Date
    Aug 2011
    Location
    flordia
    Posts
    101
    Skill Level
    repairs/rgh
    Thanks
    1
    Thanked 14 Times in 12 Posts

    Re: NandPro v3 on win7 x64 Problems

    i try to install that dlportiq.dll in my nand pro3 folder and the window opens and closes right away

  8. #8

    Join Date
    Feb 2011
    Location
    Las Vegas USA
    Posts
    301
    Skill Level
    Modding/PC Systems
    Thanks
    62
    Thanked 61 Times in 49 Posts

    Re: NandPro v3 on win7 x64 Problems

    You need to use a DOS Prompt to run Nandpro, I've ran this win7 64 bit and it's a go

  9. #9
    Senior Member
    Join Date
    Aug 2011
    Location
    flordia
    Posts
    101
    Skill Level
    repairs/rgh
    Thanks
    1
    Thanked 14 Times in 12 Posts

    Re: NandPro v3 on win7 x64 Problems

    thanks will try that

 

 

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •