Similar Threads

  1. [RGH] Getting Flash Config: 0x00000000 on trinity QSB V3 and JR-Programmer install
    By adamp2006 in forum J-Runner Official Support
    Replies: 8
    Last Post: 9th March 13, 20:04
  2. [RGH] Flash config 0x00000000
    By unkn0wn.92 in forum RGH / JTAG 4 Noobs
    Replies: 13
    Last Post: 7th March 13, 07:51
  3. [RGH] Flash Config: 0x00000000
    By athoz in forum The Noob Room
    Replies: 13
    Last Post: 20th January 13, 02:44
  4. Flash Config: 0x00000000
    By splify in forum The Noob Room
    Replies: 21
    Last Post: 1st November 12, 17:54
  5. [RGH] Flash Config: 0x00000000
    By KBTech9 in forum RGH / JTAG 4 Noobs
    Replies: 10
    Last Post: 25th June 12, 23:18
Page 1 of 3 123 LastLast
Results 1 to 20 of 44
  1. #1

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Flash config 0x00000000 trinity



    It's on dash 14719. Any ideas?

    Sent from xcover using Tapatalk 2

  2. #2

    Join Date
    Jul 2010
    Location
    Colne, Lancashire (United Kingdom)
    Posts
    11,867
    Skill Level
    JTAG/RGH Installs & Repairs
    Thanks
    819
    Thanked 4,492 Times in 3,590 Posts

    Re: Flash config 0x00000000 trinity

    Is this the error you get when using J-Runner?

    If so, try a test read with NandPro (nandpro usb: -r1 test.bin).

    Failing that, ensure your NAND-X drivers are correctly installed and that the PSU is connected to your console but your console is powered OFF.

  3. #3

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    Done that, removed the pins and soldered the wires directly, same error. One more thing, when I hook up the Nand-X the box won't start at all. I gess the wires are responsible for that, I'll try with the other NAND-X wires
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  4. #4

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    Changed NAND-X wires with new ones, still the same, drivers are correctly installed, see the screenshot.
    Attached Images Attached Images
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  5. #5

    Join Date
    Jul 2010
    Location
    Colne, Lancashire (United Kingdom)
    Posts
    11,867
    Skill Level
    JTAG/RGH Installs & Repairs
    Thanks
    819
    Thanked 4,492 Times in 3,590 Posts

    Re: Flash config 0x00000000 trinity

    If your console won't even turn on when the NAND-X wiring is in place, that tells me there is a short or something somewhere.

    You haven't powered the console on at any time when the NAND-X was connected and powered on have you?

  6. #6

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    With the new wires the console boots normaly when connected to nand-x, forgot to mention.

    One other strange thing, the SN on the case is different from the one on the MB...it could be a corona with HANA chip, I heard that they were a few made, is that possible?

    ---------- Post added at 20:09 ---------- Previous post was at 20:08 ----------

    Also, there's a button on NAND-X, dunno what's for, could be 4 reset?
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  7. #7

    Join Date
    Jul 2010
    Location
    Colne, Lancashire (United Kingdom)
    Posts
    11,867
    Skill Level
    JTAG/RGH Installs & Repairs
    Thanks
    819
    Thanked 4,492 Times in 3,590 Posts

    Re: Flash config 0x00000000 trinity

    Can you post an image of your new wiring configuration please.

    Corona boards don't have a visible HANA chip, it is embedded into the Southbridge as far as I'm aware.

    That is indeed a reset button, have you tried holding it for a couple of seconds?

  8. #8

    Join Date
    Dec 2011
    Location
    london uk
    Posts
    491
    Skill Level
    flashing rgh and tagging
    Thanks
    97
    Thanked 176 Times in 128 Posts

    Re: Flash config 0x00000000 trinity

    correct me if I am wrong and reading this incorrect

    With the new wires the console boots normaly when connected to nand-x, forgot to mention

    you have nand x installed to wires and switched console on? . If so there's your problem you have blown your nand x

  9. #9

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts
    Here's the pic of the new install. Did reset NX, still the same. I have another trinity to rgh, I'll try to see if it's working. I don't think it's NX fault since I've used it on a falcon earlier

    Sent from my xcover using Tapatalk 2

    ---------- Post added at 20:33 ---------- Previous post was at 20:30 ----------

    And yes, the console starts with NAND-X installed, but, after I plug the USB out then on it wouldn't start anymore
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  10. #10

    Join Date
    Feb 2011
    Location
    Southern California
    Posts
    315
    Skill Level
    modding
    Thanks
    36
    Thanked 126 Times in 65 Posts

    Re: Flash config 0x00000000 trinity

    Quote Originally Posted by axelll View Post
    Here's the pic of the new install. Did reset NX, still the same. I have another trinity to rgh, I'll try to see if it's working. I don't think it's NX fault since I've used it on a falcon earlierLink To Image

    Sent from my xcover using Tapatalk 2
    Did you not remove the motherboard from the metal case? From that picture it looks as though it's still in the case... which means it could very well be shorting, due to excess solder that's pushed through the bottom of the headers.

  11. #11

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    Tried to flash the CR with NAND-X and it's working, it's a strange problem and I don't know its cause... :-)
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  12. #12

    Join Date
    Jul 2010
    Location
    Colne, Lancashire (United Kingdom)
    Posts
    11,867
    Skill Level
    JTAG/RGH Installs & Repairs
    Thanks
    819
    Thanked 4,492 Times in 3,590 Posts

    Re: Flash config 0x00000000 trinity

    Quote Originally Posted by axelll View Post
    yes, the console starts with NAND-X installed, but, after I plug the USB out then on it wouldn't start anymore
    You powered on your console with the console and USB cable connected to the NAND-X?

    Did you try NandPro like I suggested?

  13. #13

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    Yes, I trid inside and outside the case. First time it was out of the case

    ---------- Post added at 20:38 ---------- Previous post was at 20:37 ----------

    Yep, NANDPRO gives me device not found
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  14. #14

    Join Date
    Feb 2011
    Location
    Southern California
    Posts
    315
    Skill Level
    modding
    Thanks
    36
    Thanked 126 Times in 65 Posts

    Re: Flash config 0x00000000 trinity

    Edit: Sorry, quoted wrong post. Basically, you may have fried your Nand-X as mentioned. Can't have the console powered on with it connected.

    But wanted to add that...

    Your Nand-X may still be able to program the CR, even if it's damaged/fried and can't read the nand... so the fact that it can program the CR wouldn't be a good indicator as to whether the Nand-X is damaged or not.
    Last edited by theagent; 11th May 12 at 19:40.

  15. #15

    Join Date
    Jul 2010
    Location
    Colne, Lancashire (United Kingdom)
    Posts
    11,867
    Skill Level
    JTAG/RGH Installs & Repairs
    Thanks
    819
    Thanked 4,492 Times in 3,590 Posts

    Re: Flash config 0x00000000 trinity

    Well I think may have gotten lucky in the sense you didn't fry your NAND-X (because Windows still sees it), try it on another console like you said above and report back.

    Quote Originally Posted by axelll View Post
    Yep, NANDPRO gives me device not found
    Check your soldering with a multi-meter, I always test with continuity if I am unsure about the connection of a wire/pad.

    The Following User Says Thank You to BL4K3Y For This Useful Post:



  16. #16

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    OK, I'll do that, but it's strange, smth inside NAND-X is shorting because the console does not boot when connected to it...

    ---------- Post added at 20:43 ---------- Previous post was at 20:41 ----------

    The brown and the green wire are "dead", with one pad of the multimeter connected to ground I get readings from all other wires except those 2
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  17. #17

    Join Date
    Jul 2010
    Location
    Colne, Lancashire (United Kingdom)
    Posts
    11,867
    Skill Level
    JTAG/RGH Installs & Repairs
    Thanks
    819
    Thanked 4,492 Times in 3,590 Posts

    Re: Flash config 0x00000000 trinity

    You shouldn't even be trying to power your console on with the NAND-X connected!

    This is how users fry their NAND-X devices !

  18. #18

    Join Date
    Feb 2011
    Location
    Southern California
    Posts
    315
    Skill Level
    modding
    Thanks
    36
    Thanked 126 Times in 65 Posts

    Re: Flash config 0x00000000 trinity

    Quote Originally Posted by BL4K3Y View Post
    Well I think may have gotten lucky in the sense you didn't fry your NAND-X (because Windows still sees it), try it on another console like you said above and report back.
    It would actually still show up in Windows, even if damaged.

  19. #19

    Join Date
    Mar 2011
    Location
    Everywhere
    Posts
    471
    Skill Level
    JTAG, RGH
    Thanks
    70
    Thanked 62 Times in 54 Posts

    Re: Flash config 0x00000000 trinity

    I didnt, until I tried with the second set of wires so I don't think that's the cause. I'll wire it up to a zephyr in 5 min to see what is NAND-X "saying"
    Modare si RGH, depanare, reparatii, diagnostic console XBOX360. Pentru intrebari - ajutor, trimiteti un mesaj

  20. #20

    Join Date
    Dec 2011
    Location
    london uk
    Posts
    491
    Skill Level
    flashing rgh and tagging
    Thanks
    97
    Thanked 176 Times in 128 Posts

    Re: Flash config 0x00000000 trinity

    blakey basically you can still fry your nand x with windows still seeing it . I have posted one to Martin it allows you to programme cr is shown in windows but wont read nand he is going to have a tinker with it . It was when i first started doing rgh my mistake . Now I know it stopped working because when I plugged my other nand x in it read the nand straight away.

    Do as suggested try another board you can always reprogramme it to version 2 and do a test in nand pro version 3 cant be tested in nandpro .
    Last edited by tonyjandc; 11th May 12 at 19:50.

 

 
Page 1 of 3 123 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •