Hello,
I am trying to glitch a Jasper, but I was only able to boot Xell and once managed to boot the hacked image. First some info and at the end pictures of my soldering.
Model: Jasper 16MB
CB: 6754 (generated hacked image with J-runner is 6752)
Dash: 17150 (generated hacked image is 17511)...
Console Type: Jasper
NAND size: 256
Dashboard version: 2.0.17502
CB version: 6723
I had RGH2 done to this console, but i changed it to R-Jtag for stability, and i'm really glad. It glitches 9 out of 10 times in less than 10s.
I used AUD CLAMP and dips 5, 7, 8 ON. As i told its smooth booting...
Hello All,
I have not followed the template, as I don't think I am far enough into the build to obtain a lot of the information requested. My apologies if this callousness offends.
I have a Jasper that I have owned for a few years, and it's been sitting on the shelf for a bit. Finally got...
I dumped the NAND with a J-R Programmer V2 3 times and they all matched with no broken blocks. I then flashed Xell to get my CPU key, and upon turning on the Xbox, I got the RRoD (code 0022).
What would be my next best step? I'm not touching anything until I get advice.
Notes: Soldering is...
I have a jasper 16MB (Nand) and everything was fine before i install the Wires (JR NAND Reader) it does something funny. I read the NAND just fine and made the back up. Also i Have a Ben-Q drive and i flashed that no problem as well with LT+3. When i plug the DVD power in i get a Black Screen...
If I use nandpro to write the ecc, is the command still
Nandpro usb: +w16 image.ecc
That's what I want to know. I don't know if same rules apply to CR4 but I would assume they do. Thanks
Console Type: Jasper
Programmer Used: SPI NAND flasher
NAND Size: 16mb
Dashboard version: e.g 2.0.17489
CB Version: 6754
Image of the CR4 XL
Detailed Description of the Problem:
CR4 wire only install. R-jtag method with aud_clamp. All solder points have been checked countless times to make sure...
Console Type: Jasper BB 512mb
Programmer Used: TIAO USB SPI
NAND Size: 512MB
Dashboard version: 2.0.16537.0
CB Version: 6754
Detailed Description of the Problem
Was the console working before you started: Yes
Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: Yes...
Hello all. About three weeks ago I posted a forum about my trinity not glitching with a CR4 XL. Its almost Christmas time, and I plan on purchasing a console from WNY Console Services. I have spent over $100 USD on a JRP, 2x CR4 XL, with no luck. I have tried two different CR4 XLs, neither have...
hello team xecuter. every time i try to use j runner which i just normal click and try to read nand it gives me this message error:
Problem signature:
Problem Event Name: APPCRASH
Application Name: JRunner.exe
Application Version: 0.3.7.2
Application Timestamp: 54a6d56a...
i have the old jasper with a dashboard of 2.0.12611.0 and am looking for someone to give me a parts list of Team Xecuter parts i would need to mod my xbox 360, or if any parts are available to mod the old console, preferably from the mod chip central website, or an equaly trusted store where i...
hi. i screwed the post_out by the xclamp, and i had the scrap the one by the cpu. is there ANY other post_out alternatives? i dont care about boot time, i just need a post_out because my cr4 is not showing a green light.
hi have a full guide for rgh 2.0 with cr rev c but they all sold out so i have to use cr4 im confused about the part where you connect the cables from the jr programmer to the cr4... is the setup different form cr rev c i have a jasper and need a cr4 jasper install guide for rgh 2.0 thanks in...
First I installed the CR4 XL with my own wires and it took about 10 minutes to boot the big block (512MB) Jasper into Xell.
Dumped cpukey via LAN, and with J-runner I created an image based on 17150 and wrote it back with NAND-X.
After that it took another 10 minutes to boot the image, and the...
This is my first time modding a console. I have a Jasper Phat console. I bought a kit to mod my console. I am nearly done and have everything soldered correctly (I hope). I still have the console open in case I need to fix anything so I wanted to ask you fine folks if there's anything I need to...
1. What Type of usb cable do i need to program http://i.imgur.com/EJzzgqx.jpg or also known as the Mtrx Nand Programer
2. Can i use The Mtrx Nand Programmer on the Coolrunner Rev C Glitcher?
3. Is it required to need any qsb's on a Jasper Motherboard
4. Diagram for the Coolrunner -> Mtrx...
So I just got an old x360 arcade. Its a jasper model with dashboard 16747. I'm completley new to xbox (never owned or used one) and I seem to can't find proper information on which method should I use to hack it on this version of the dashboard and play downloaded games on it? I found some old...
I'm really new to JTAGing and RGHing and the like so please excuse my ignorance. I understand the general basis of JTAGs and RGHing but it seems like there's a new version to mod your xbox every other week and I don't know where to start. So if someone could show me an up to date guide or just...
Hi guys, Just registered today, been looking around the web, and mostly on this forum for help for a while to jtag my xbox. a lot of info out there is confusing, as things change in the last 7-8 years asfar as what can be done on what machine.
quickly, I started with a usb spi flasher and soon...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.