rgx

  1. E

    DGX rgx v1.1s xbox 360E corona v6 4gb nand. red light and shut down

    hello. i am having a problem with my xbox 360E corona v6 4gb nand. the rgx is glitching and it seems like it is working fine but then the ring of lights center turns red and the fan speeds up and it just shuts off. if i flash back to the stock nand and disconnect the 5v wire it boots fine. have...
  2. S

    Won't Glitch if Xbox is hot

    Let me start by saying that I did a search for this matter and couldn't find anything specific to my issue. If i'm wrong feel free to point me in the right direction. Thank you I recently installed a TX DemoN into my Corona v3. I'm using an RGX as a glitch chip. My setup works GREAT and it is...
  3. A

    RGX Debug Led On Front Panel without Need For Diode

    Ok So this is my first Tutorial so dont hate too much:tongue: NOTE: allways check your connections and work with a multimeter and ALLWAYS USE FLUX!!!!! ( There Are Many different ROL Board configurations and not all will work with this exact method check the connections for your specific board...
  4. J

    DGX RGX Help

    Hi so I have a trinity mobo dash 16203 I was thinking of doing the rgx but...it's very unclear to me how it works so please help....here is how I think It works 1 Dump Nand 2 Flash DGX into Rgx with the Files 3 install RGX 4 Boot Console and enjoy unsigned code This is how I think it...
  5. A

    GENERAL Lifted Demon Pads and Need Alternates

    Hey Guys, this is my first post in these forums and for the first time have found myself in over my head! lol. I have done well in the range of 100 rgh2 installs and 20+ demon installs, Well tonight i tried to install (for the first time) a demon on a corona v1 MOBO now iv really screwed myself...
  6. Biopcb

    RGX jasper 16mb, 16202, hardware purchase questions

    I have a question, I haven't modded a 360 since 2008, I want to do my Jasper 16MB, 16202 I tried dumping the nand via homemade LPT cable, I did 30+ dumps, I used a checksum app to check them, non of them match. I tried NandPro 2b and 3.0, never have the correct FlashConfig number. I was...
  7. DreamZ

    RGX success with trinity

    Managed to finally get a trinity to glitch using RGX. i used a dgx1.0, wrote timing file C on it and it boots VERY VERY fast. Very impressed with it, It glitches on average within 3 glitches. most of the time pretty much instant :) ive attached a few photos, these were taken when i first...
  8. L

    RGH Red Dot Secondary code 0021 on Stock Nand after failed RGH (trinity)

    TX Product(s) used: CR3 Lite/RGX Console Type: Trinity NAND size: 16 Dashboard version: 16203 CB version: 9231 I have done around total 50 RGH/JTAG, around 10 slims. Description of problem: I dumped nand twice. They were good. After attempting to use an RGX/CR3 Lite to get key, I wanted to...
  9. musicdude509

    RGH RGX Help; Failed to write block error

    Hi, I have a Falcon with dashboard 16202 that im trying to rgh2 and Nand-x and collrunner rev C and V2 Qsb's. I am using the FALCON.ECC that comes with the newest J-Runner...
  10. S

    DGX Is my DGX V1.1s glitching?

    Hey all, Trying to retrieve my key here so I can install a LTU pcb board. I have a Corona V3 board and have bridged R2C6, R2C7 and R2C10 as all had missing resistors. I have got two successful reads of my NAND using JR Programmer V1. I have installed a post fix adapter. I have installed a...