stby_clk

  1. K

    GENERAL had to rewire STBY_CLK point (R3B15 resistor on Slim)

    messed up my STBY_CLK point so had to rewire used this method: http://team-xecuter.com/forums/showthread.php?88489-TuT-Alternate-STBY_CLK-Install-STBY_CLK-Fix-for-Slim-and-Phats-(Noob-Friendly) this worked and the xbox now powers on and runs stock nand and have installed cr4. The issue is the...
  2. P

    RGH STBY_CLK damaged

    Hey guys, yesterday I was desoldering my coolrunner rev C. from my Jasper 512mb motherboard, so I could safely bridge cap, but I accidentally pulled the STBY_CLK wire, and the pad came off along with it, so my console wouldn't power on, even though the coolrunner would still flash red if set to...
  3. blakhawk

    [CR3Lite] Xbox no power when STBY_CLK connected

    TX Product(s) used: CR3 Lite + Slim Demon Console Type: Trinity NAND size: 16 Dashboard version:2.0.16203 CB version: N/A Screenshot of NAND details from J-Runner: N/A J-Runner log:Attached Description of problem: Console working correctly prior to mod attempt. 1. Checked Demon before...
  4. Endless Options

    FIXED Jasper not Booting, Is this why?

    Ok so i was going through my dead xboxes and this jasper seemed to have no problems besides the Stby_Clk. This xbox doesnt boot and i am thinking the point underside of the hana chip is why. I attemepted this jasper a long time ago (Roughly febuary 2012) you guys can you maybe help me out on...
  5. L

    Jasper won't boot with CR3 Lite soldered in

    Hi! I'm new to the RGH, but I did a lot of reading. I decided to RGH my 256MB Jasper and bought a CR3 and a NAND-X. I followed a Tutorial and read my Nand twice before doing anything else. Then I flashed a RGH1 Jasper xsvf file onto the CR3 and soldered it in. I tried to boot the XBOX with...
  6. L

    Killed Resistor at C3B2 R4B24 (Point B), Recoverable?

    I was trying to solder onto Point B (Orange Wire) when I was having issues with the pad not letting me stick solder to it(yes I did use flux). I though I finally got it on when I realized it had connected to the resistor next to it and then I realized too late, it had pulled it off. It also...
  7. S

    RGH 3 rrod error 0010 after coolrunner installed

    i understand that perfectly good xboxs can fail right when you take them out of the case. I think i caused this by pulling the mobo out via cpu heatsink and when i turned it on it went fubar. my nand reads fine and after plenty of messups on the stby_clk i finally got the xbox to turn on, but...
  8. M

    Alternate points for R4B24

    One thing not discussed in previous posts regarding R4B24 is an alternate point for the trace on the HANA side of the resistor. On the underside, look for the line that goes to C4N27. There is a column of pads about halfway between the cap and the label. (blue dots in pic). The point right...
  9. S

    Stby_Clk resistor repair

    really pissed off that i didnt just use the alt point in the first place. but anyways, while trying to repair the point (not the resistor), the resistor itself fell off. ive seen another post where a guy used a resistor connected to a wire and the point to where the resistor is closest to the...
  10. J

    GENERAL What range of a Digital MultiMeter Do I need to check xbox

    Hi, Noob Question... I bought a 15 range MultiMeter to check for shorts on the xbox 360 motherborad and am wondering will that do the job? If not what range do I need? and Could you point me in the right direction in how I could use it on the xbox. I want to check if the resistor at STBY_CLK...
  11. L

    [USA] Looking for a Pro to help repair a lifted R4B25 pad

    Hey, I'm in the USA, Indiana. I've done about 5 RGHs successfully. I had a friend that tried to do his instead of asking me to do it and he lifted the R4B24 pad and now his xbox won't power on or let you read the nand. I dont really want to attempt to repair it and was wondering if a pro in...