xell

  1. I

    RGH Another Problem.

    Hi everyone, I got yet another problem. I've done te following: - Read nands - Compaire nands - Make a .ecc - Flash the .ecc - Prog. coolrunner (for Falcon) - Install coolrunner - Launch Xell - Get keys. - Make a new nandflash.bin with cpukey - Flashed with .elf in Xell All that went well...
  2. J

    ANSWERED I can boot dash but not xell.

    Hi guys, i've made a RGH on my jasper 512 and I can boot on dash 14xxx play games and homebrew, but if I press the eject button xell doesn't launch. I made ECC and DASH IMAGE with 360 Multi Builder 0.7. I cant boot xell neither with reset button nor with xelllaunch at dash. I've tried with...
  3. H

    ANSWERED red light psu after write xell

    so im attempting to jtag my xenon motherboard i used the quick solder from nand-x manager to dump my nand 5 times all identical with a bad 208 in 3ff i wrote xell and got an e79 then attmepted to restore nand by hitting write bin (used original dump) in coolshrimp jtag tool now when i turn it on...
  4. O

    JTAG Jasper 6723 16MB to 14699 -> Xell boots, Dash doesn't

    Hey there, i have the following Situation. Console is a Jasper 16MB with CB6723 on Dash 13599. Wiring is aud_clamp. There is no backup of original NAND (ye, bad, i know), only of the created freeBoot-Images. I wanted to Update to 14699, so i did as usual: dump current nand via flash360, fire up...
  5. G

    Cooleunner trouble, boots xell but not freeboot image.

    Hoping I can get some help, I've followed tutorial and got so far, now I'm stuck. Installed QSBs, dumped the NAND and compared, generated ECC file, programmed and installed Coolrunner, wrote ECC, boots Xell fine (green flashing light on Coolrunner). Then I wrote down the CPU key and made...
  6. G

    Yet another Xenon that won't boot xell?? HELP!

    ‎alright guys, here is the low-down, I have updated my jtaggable xenon (with a CB of 1888) from kernel 5766 to the 7mb (no avatar data) 7371 NXE dash. I had the nand-x (and Jtag QSB's) installed BEFORE I updated to 7371. (oh yeah :3 I used the damn QSB's) soooo I then proceeded to dump my...
  7. W

    CPU key problem

    JTAG is not recognizing my CPU key! I've seen a few posts about this, but I'm still having problems. Using JTAG tool 3.0, I've dumped the nand successfully with no errors, at least 10 times now. I've been able to boot Xell to get my cpu key, but when I type it back into KV info, I get this...
  8. S

    How do I restore my original nand with nand-x to remove e79 error?

    I have a falcon motherboard. I have the nand x with qsb and are successfully soldered. the nand x can read the nand without any errros along with writing xell/xellous. I used the alternate jtag points along with the jtag qsb used here here . for the red wire, i used option b, tried booting xell...
  9. S

    Nand-x issues =[..PLEASE HELP!!

    Ok, so I get my nand-x fully installed I did the actual jtag part different because the quick solder board was burned so I use cool-shrimps jtag tool 2.12 dump my nand I install xell grab my cpu key install freeboot and when I turn my 360 on all it does is go back to xell and give me this...
  10. M

    Pesky Nand and Xell (E79)

    Didnt want to highjack anyone elses thread so I thought I'd put a Q & A together as I'm stuck :( So, Got my Nand-X installed on a Xenon MB. Dashboard is updated to 7371. Kernel 1903. DVD Drive Not Connected Power in but Not on I've soldered the wires directly to the MB rather than the pin...