0022 e10 after Coolrunner install.

Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Read all the stickys - especially the ones in this section. You agreed to do so when you accepted the new rules.

No information
No pics
= no help.
 
D

djxxx

VIP Member
Mar 20, 2006
331
33
Planet Earth
I will look into my crystal ball that TX made me.....lol
Need more info mate with good quality images
 
G

gamehawk55

VIP Member
Mar 21, 2006
202
33
Canada
www.chaotic-consoles.com
Could possibly be a broken solder joint under the GPU or CPU. Most likely GPU though with an E10. I've had that error happen to me plenty of times with xenon and zephyr boards. Releasing the T8 screws from beneath the heat sinks seemed to have caused too much pressure to be taken off them and caused an already on the edge joint to disconnect. I used the lazy mans reflow (overheating GPU) to fix the error once all the xclamps and T8 screws were tightly back in place and they have been fine ever since. But I may have just been lucky. You may have to reflow the GPU.
 
F

freake

Full Member
Feb 9, 2012
65
0
Ok if you want pics sure I'll get some now but there isn't really anything to take pics of other than the motherboard..
 
T

tonyjandc

VIP Member
Dec 30, 2011
481
0
london uk
ERM two console's in one day seems odd to me . But then again who am I to complain this and another thread about 3 rrod after fsd

was refering to another thread no pics do people think we are magicians?
 
Last edited:
F

freake

Full Member
Feb 9, 2012
65
0
socalbill said:
most likely you bridged the test point and the cap right next to it
Click to expand...
Ok I will upload a pic of that point (both sides) tell me if you see anything wrong if not can you tell me where to look and what to look for.

---------- Post added at 12:52 ---------- Previous post was at 12:48 ----------

Bottom


Top
 
socalbill

socalbill

VIP Member
Nov 30, 2011
356
0
Valhalla
most people with 0022 problem bridge this point on cpu pll bypass....your cpu reset points are fine, they are almost impossible to f up
 
  • Like
Reactions: freake
F

freake

Full Member
Feb 9, 2012
65
0
Ok just seen my console is actually a Jasper console not a Falcon could the RROD be caused by using the 175w power supply? I was using it before for like a min and it was working.

Also could turning on the console with the coolrunner programmed for use with a Falcon caused it?

---------- Post added at 13:15 ---------- Previous post was at 13:11 ----------
socalbill said:
most people with 0022 problem bridge this point on cpu pll bypass....your cpu reset points are fine, they are almost impossible to f up
Click to expand...
Yh I did bridge them but i think i got it back to normal again but im not sure. My camera wont focus that close to the board so I can send a decent pic of that. Can you tell me any methods of fixing it just in case.
 
F

freake

Full Member
Feb 9, 2012
65
0
ok, that point doesnt really luck bridged but it might be bridged with that square black thing underneath it.

---------- Post added at 13:33 ---------- Previous post was at 13:26 ----------

Ok I've found out whats I bridged! The thing in the picture you said may be bridged with that point well that thing itself is bridged :S I can just see there is a tiny bit of solder on the side of it on the bottom connecting either side of that component together.

How on earth do I fix that without burning that component?
 
You must log in or register to reply here.