RGH 0022 on original nand aFter incompleted RGH

[x23are]

hi
at first sorry for my english
i have jasper 16MB and i can dump Nand perfectly .
after that i made image_00000000.ecc and wrote that compeletly
i try try try an try. but no Xell displayed . after look i found problem with wiring . that was wrong
while i changed cable place GND & VCC in 1 sec shorted .
console was in stand by . and red Light on CR turned off .
unplged Power and pluged it again and it work . after that when i torn on console green light blinked ever 5 sec an Xell not comming up again .
tested again with 68 cap between A and GND .
no result .
at Final i decided flash back original NAND . with NANDpro and -r16 and then -w16 i wrote NAND .
sudenly i have 0022 error in 25-27 sec .

i dont think its for Damaged pad or lifted .
its not my first time that i want go on RGH .

CR Removed and Pads are OK .

i think GPU damaged after that short that i explained.
and it can not For LDV . becuse i did not have Xell NEVER .

help me please.
thanks .

 

[WNYConsoles]

You likely had a bad ECC and if you wrote the ECC then did nandpro usb: -r16 nand1.bin then all it did was overwrite your original nand1 dump with the same nand1 dump but with the ECC included, therefor without CoolRunner you will get 0022

You need to write your second nand dump back, which would be nandpro usb: -w16 nand2.bin

Give that a try, bet it works out for you.

 

[x23are]

You likely had a bad ECC and if you wrote the ECC then did nandpro usb: -r16 nand1.bin then all it did was overwrite your original nand1 dump with the same nand1 dump but with the ECC included, therefor without CoolRunner you will get 0022

You need to write your second nand dump back, which would be nandpro usb: -w16 nand2.bin

Give that a try, bet it works out for you.

thank u so much
but NO
i dumped 3 nand.bin
and all of them are OK and Same
before that i made ecc i have them .

i made ecc with FreeBoot .
with name : image_00000000.ecc

on other consol when i write original nand with -w16 command
all of them comming up without any error
but this one

 

[x23are]

i found something in xbox-experts

This error is caused by a bridged/shorting solder joint under the GPU, (H)ANA-chip or in between.It can also be power related though, for example if you are drawing power from one of the regulators that power the GPU and HANA-chip.Can also be a component that is missing or damaged so look for missing parts near the GPU and the HANA chip.

what you think?
can this be my solution ?

 

[AteOeight]

Try +w, instead of -w... works in some cases.

 

[x23are]

Try +w, instead of -w... works in some cases.

no
dont work . same result : 0022

when i wrote original nand . read again with -r16 and it is same with my first ifrst first dump nand.bin

 

[dirtyscout]

try erase the nand then flash back the stock nand ..had this issue when i was recovering a dvd key the only time i had to recover a dvd key

 

[x23are]

try erase the nand then flash back the stock nand ..had this issue when i was recovering a dvd key the only time i had to recover a dvd key

erase 10 time and wrote back .
but this not work .
:frown:

 

[Martin C]

upload your original NAND dump.

 

[x23are]

upload your original NAND dump.

thank you martin
thank you
ok . upload 3 hours later when i went to home.
don't you think its about my bridge/short accidently and missing component near GPU ?

 

[Martin C]

At the moment, it's hard to say.

 

[x23are]

here is my 2 nand dumped at first

http://www.mediafire.com/?d65dj4a76b6mf76

 

[Martin C]

NAND dumps look ok. Flash back to the console using a nand-x and nandpro, remove all wiring and try again.

 

[x23are]

NAND dumps look ok. Flash back to the console using a nand-x and nandpro, remove all wiring and try again.

try this last night .
and now again.
then read again and when i compare those . both are same .
but don't work .


my r7r17 and other two resistor near that are 8.8Kohm . on other console they are 10 Kohm .
is this NORMAL?

really whats happened in my console dear martin ? :facepalm:
i think just you can help me .

 

[Martin C]

Your console was on 13599 - did you update at all?

Try flashing the created RGH image again and with the coolrunner in place, boot with the eject button.

 

[x23are]

Your console was on 13599 - did you update at all?

Try flashing the created RGH image again and with the coolrunner in place, boot with the eject button.

yes
13599

and No . i don't update that . in fact after this RGH my dashboard not coming up . and i could not update that .

ok .thank you again . test it tonight . in my country : 4 hours later

 

[x23are]

i forgot to say one unusaul thing.
cpu pll bypass voltage is 1.1 v in my multimeter.
but>>>.>>>>>
i tested it in other jasper and falcon mobos.
the voltage was 0.06 !!!

 

[Martin C]

Remove R7R17 and check the resistance.

 

[x23are]

pll voltage is ok
my mistake
it is 0.08

and r7r17 is 8.5 kohm
r6r9 and r6r7 are same 8.5 kohm

i'll trying install coolrunner again and power up by eject .

maybe it is helpful
when i write image_00000000.ecc on console without CR installed console work good and no 0022 error code appear .
but no video and audio that it is normal i know.

 

[x23are]

dear martin
with CR installed and eject don't work again
green light blink ever 5 sec and for 7-8 times .
then nothing

next time green light blink only one .
then nothing