i flashed my 0225 drive using the unlocked pcb no solder solution. it plays backups just fine it just does not eject. at all. help would be greatly appreciated.
LITEON DG-16D4S - SLIM 0225 drive wont eject after after flashing with latest firmware
- Thread starter keezykee
- Start date
Dosk3n
VIP Member
I'm new and flashed my unlocked pcb today for the first time, did you should hit the Outro / ATA Reset button a few times - this solves the "Open Tray Error")
xbox360 hacker
BANNED
EDIT: i should read previous comments properly before commenting :facepalm::facepalm::facepalm::facepalm::facepalm::facepalm::facepalm:
Last edited:
The way I read it demon2011 was offering a possible solution to the OP......:rolleyes2:
Some things get lost in translation
xbox360 hacker
BANNED
No prob matey, just thought i'd ask if he had pressed the Outro / ATA Reset button a few times as i saw in the tut that this can happen.
I have a problem that has nothing to do with this thread, but that's a whole other story lol
@OP - just double check your connection of the wires in the connection block...maybe check continuity....also - does it eject when out of the xbox (i.e. when using a ck3)? or when using a controller?
@OP - just double check your connection of the wires in the connection block...maybe check continuity....also - does it eject when out of the xbox (i.e. when using a ck3)? or when using a controller?
When you re-assembled the drive what way were the wires that connect from PCB to no solder board positioned? Were they under the black housing or between the black housing and the case. Some people have left the wires above the black plastic and when they replace the case it clamps the wires and can cause problems like no eject or constant ejecting.
you could try this bud if you had looked abit more in the forums you would of found this
http://team-xecuter.com/forums/showthread.php?t=70138
if i helped please thank me
Teajunkie
VIP Member
Thats not his issue he is using a tx unlocked pcb
It's going to be your wires in the block buddy the black and red are the eject motor check them first.
It's going to be your wires in the block buddy the black and red are the eject motor check them first.
Thats not his issue he is using a tx unlocked pcb
It's going to be your wires in the block buddy the black and red are the eject motor check them first.
lol sorry my bad lol thourt he did kamakize didt read proper lol my bad
yes the problem was indeed the wires in the block. i didnt lock them in correctly. it works like a charm now. a big thanks for everyone who posted
Hey bro I did the same thing connected wrongly now my disc not ejecting what should I do help plZ?
Im using the original 0401 PCB board so i havn't touchany cables.
So i have removed the back and top case of the drive and i can now see what the problem is. When i open tray place a game in then close the tray the laser is moving but the motor to spin the disk is not. So basically the disk is not spinning.
Any ideas or you reckon i need a replacement board?
Cheers
---------- Post added at 18:47 ---------- Previous post was at 18:38 ----------
woops sorry im in the wrong section. Disregard my last messages.
So i have removed the back and top case of the drive and i can now see what the problem is. When i open tray place a game in then close the tray the laser is moving but the motor to spin the disk is not. So basically the disk is not spinning.
Any ideas or you reckon i need a replacement board?
Cheers
---------- Post added at 18:47 ---------- Previous post was at 18:38 ----------
woops sorry im in the wrong section. Disregard my last messages.
Teajunkie
VIP Member