14717 Update mistake - how to fix?

[roym899]

Hey guys,
i have a huge problem. I know i was quite stupid but maybe you can help me fixing it.
So here it is: I have a Xbox 360 Slim with an installed Coolrunner and a Cygnos 360 for reading / flashing the NAND and for dual boot.
Everything worked fine on the 14699 Dash. Now after xebuild for 14717 was released I wanted to update the original NAND to read it and building the new hacked image. But I forgot that the xbox won't start after updating the NAND and it restarts during the update process.
So it downloaded the Update tried to restart and the console didn't boot anymore. Nor did the hacked NAND.

So I opened the console and built in the relay so when my cygnos is turned off the coolrunner is off too. This worked out too, but know I have the problem that my xbox doesn't starts anymore, in neither mode.
In Normal Mode I get a RLOD after some time, and with the cygnos turned on I only get a blinking green LED and the Coolrunner blinking red in periods of time.
I tried many different dumps I had and none works.

What can I do to fix this?

Please help me :frown: I'm so sad.

 

[RnRdude]

you need to wait for the new release.. or try newest multibuilder create an new image put cpukey... and let it build new image.. then flash that one with usb flasher nandx.

 

[roym899]

you need to wait for the new release.. or try newest multibuilder create an new image put cpukey... and let it build new image.. then flash that one with usb flasher nandx.

I don't really get this. With release, do you mean J-Runner? but isn't that one more or less the same then xebuild gui just with more features?
Or do I need new timings for the coolrunner or so?

 

[legitmod]

What he means is look here http://www.team-xecuter.com/forums/showthread.php?t=74059 an download 360_Multi_Builder_v0.8

 

[redonep4]

Has been released new 360 multi builder v0.8 and U can use it to build new image for your rgh console

 

[roym899]

Ok, i try to do right now, but when I build a Retail Image 14717 it says "could not read cba_9230.bin (-1)"
"ERROR: cirtical bootloader files are missing, cannot proceed!"

??

 

[WNYConsoles]

If the official 14717 update was applied you need to make sure you can boot the stock retail dash successfully before doing anything. Once your XBOX is booting retail stock 14717 you will need to dump the nand again and create a new image with Multi Builder v0.8 along with your CPU Key.

 

[Hackerjac]

i just tried multibuilder 0.8 also, got the same error
but xeBuild GUI 2.0_FINAL could build the image for me

 

[roym899]

Hm I tried to get the original 14717 but the update failed. And now it always says when I try to start "systemupdate stopped" (not sure if this is the exact translation because it's in german for me) It also says it can'T read the update from the HDD although the HDD is plugged in...

 

[WNYConsoles]

Dump the nand first to confirm the CB was updated, if it wasn't then you can likely flash back your original NAND or build a hacked 14717 image with your original NAND.

If the CB was updated then you need to finish the update with official 14717 on USB. Once booting dump the nand again and re-create your hacked image.

 

[fullban]

Hm I tried to get the original 14717 but the update failed. And now it always says when I try to start "systemupdate stopped" (not sure if this is the exact translation because it's in german for me) It also says it can'T read the update from the HDD although the HDD is plugged in...

just build a retail nand with your dump should work cause when it fails its already flashed the nand ...well it had in my case

 

[roym899]

Updated via USB now and original Dash loads up normally. Then I created a hacked image from a new nanddump and putted it on the cygnos.
Now my Hacked Dash is not boting. I think it's a problem with the coolrunner, because theres no green light flashing when starting the xbox, only red light flickering a little bit. Do you know from what that come? GND or VCC? Because these are the only ones I connected to the relay. (although I don't unterstand why I have to connect the GND to the relay but the diagram says so)

 

[roym899]

Fixed the strange light on the coolrunner. No blinking green like normally but it doesn't glitch.
Image should be alright. Do I need new timings for my coolrunner? Or could I just use my old 14699 Image and increase the LDV by 1?(if so could someone tell me how i do this?)