RGH 1st attempt to a corona need some advice
- Thread starter fokeiro
- Start date
this is what i did basically :
extracted retail nand, flashed ecc, booted xell, got cpu key through ethernet, created custom nand, flashed back, didnt touch any settings at all , i mean it works with boot between 1-2 mins, now im just curious what went wrong for for curiosity maybe someone else did have same symptoms
extracted retail nand, flashed ecc, booted xell, got cpu key through ethernet, created custom nand, flashed back, didnt touch any settings at all , i mean it works with boot between 1-2 mins, now im just curious what went wrong for for curiosity maybe someone else did have same symptoms
Beaver_Buffcoat
BANNED
Did you create the ECC from your retail NAND dump?
[video=youtube;oRd00FmXbvo]http://www.youtube.com/watch?v=oRd00FmXbvo[/video]
[video=youtube;nVT_9a2IrHQ]http://www.youtube.com/watch?v=nVT_9a2IrHQ[/video]
Credit to Keil423
Last edited:
Beaver_Buffcoat
BANNED
What happens when you power on with the controller? If you have wired and wireless controllers, try them both, and check your RF module connection.
Last edited:
Beaver_Buffcoat
BANNED
Is this console intended for your personal use? If so, leave it and use normally. You can revisit this issue later if any problems come up.
I'm under the impression that the power button itself is the problem. Look carefully, test for continuity. Have someone press the button repeatedly while you probe the switch points (with the RF module disconnected from the Xbox).
Nevermind. Pressing power turns the Xbox on, but no boot. Disregard the switch test.
Last edited:
Beaver_Buffcoat
BANNED
Officially out of ideas here. If anybody reading this thread has had this problem (power button on console=black screen, DVD eject= boot FSD), your input would be greatly appreciated.
ill try to boot again with power button after updated nand to latest dash and ill post result, for now im just double pressing eject quick so tray dont come out to boot
Now WTF this sh*t is palying trick on me....well.since it was working i decided to put it back together closed the case...put it sideways instead of laying down attempt to boot with eject....f**king xell comes up everytime now...and now boots even faster wtf is going on lmao
Last edited:
sorry ultimate , i just subscribe , i dont know , i will delete my post from here .
all my respect for team -xecuter
all my respect for team -xecuter
Beaver_Buffcoat
BANNED
I suggest that you start from square one. Start by disabling the Coolrunner (switch to PRG or disconnect 3.3v). Then, check that your NAND wiring is all good (use a bright light and magnifying glass if you have to). Load up your first retail dump in J-runner and flash to the console. Disconnect power, reconnect power & try to boot retail with power button.
Beaver_Buffcoat
BANNED
I will attempt to clarify the problem here for any readers of this thread.
http://team-xecuter.com/forums/showthread.php?t=147053&p=1015418&viewfull=1#post1015418
http://team-xecuter.com/forums/showthread.php?t=147053&p=1015418&viewfull=1#post1015419
I believe the RGH NAND image that fokeiro built in J-runner included 16756 dash/kernel which is not compatible with Dashlaunch 3.12. I suspect this as the cause of black screen on normal boot. FWIW
http://team-xecuter.com/forums/showthread.php?t=147053&p=1015418&viewfull=1#post1015418
http://team-xecuter.com/forums/showthread.php?t=147053&p=1015418&viewfull=1#post1015419
I believe the RGH NAND image that fokeiro built in J-runner included 16756 dash/kernel which is not compatible with Dashlaunch 3.12. I suspect this as the cause of black screen on normal boot. FWIW