2 red light rings after RGH

[ARUNCREATIONS]

Hi
I have done rgh in a falcon console(it has been fixed for rrod at past and worked fine before RGH).

1.I can get into xell witj no problem no redlights..
2.After BUILD 14699 glitch image i got 14699 dash also..but after this whenever i power on my console i got 2 red light rings( D1&D2)..is it a overheating problem i have to fix it again? or anything new problem of my rgh install...?:frown:

 

[jtag360.nl]

Are the fans spinning faster and faster before you got 2 red lights?

I think the heatsink of the CPU is the problem.

 

[Martin C]

What's your secondary error code?

 

[ARUNCREATIONS]

Instant 2red lights black screen but boot well into xell no redlights

 

[Martin C]

did you say lights 1 and 2 are on, not 1 and 3?

If so, it's not overheating. How did you write your NAND image?

 

[WNYConsoles]

Does it post 2RROD instantly or does the dashboard boot and run for a minute then post 2RROD? If the latter, check that the fan spinning and it if isn't make sure it's plugged in

 

[H3rmaN]

What's your secondary error code?

This

did you say lights 1 and 2 are on, not 1 and 3?

If so, it's not overheating. How did you write your NAND image?

....and this!

Does it post 2RROD instantly or does the dashboard boot and run for a minute then post 2RROD? If the latter, check that the fan spinning and it if isn't make sure it's plugged in

See the OP's quote below, boots fine into XeLL, but instant RRoD when trying to load freeboot.

Instant 2red lights black screen but boot well into xell no redlights

@ the op, as Martin has said, what's the secondary error code?

 

[ARUNCREATIONS]

Oops...
first XELL boot very fine show cpukey and so & so wihout redlights..
i got few times into fsd after glichimage written(14699 dash)
for note ..this board has done rrod in past and befor RGH it works fine with flashed benq drive.
but now i get instant 2 redlights with blackscreen as show below
http://www.imageuploading.net/images/14184/2-red-lights

is it overheating issue or anything else..no second error code

 

[KhaineGB]

Like Martin said, how did you write your Freeboot image?

Nandpro? rawflash?

 

[H3rmaN]

The 2 LEDs highlighted in that image are 1 & 3, not 1 & 2 as you said earlier. It will have a secondary error code if those 2 are flashing.

Are you holding the sync button and pressing eject? Instant 2RL means there is no (or poor) contact between the CPU & heatsink, so make sure it is securely attached with sufficuent thermal paste (not too much though). If it runs for a short time then turns off with 2RL it is overheating, again, same applies, make sure both heatsinks are securely attached and that there is sufficient thermal paste.

 

[ARUNCREATIONS]

Thanks H3rmaN...
i wrote freeboot image with rawflash..
as u said it may be overheating problem
i will look in cpu&heatsink

Thank u to all for ur contribution

 

[Martin C]

You still didn't provide a secondary error code......

 

[ARUNCREATIONS]

i cant see any error code
sorry the 2 redlights are not 1&2 its 1&3 as the below image

http://www.imageuploading.net/images/14184/2-red-lights

 

[KhaineGB]

You won't get your error code on the screen.

Hold sync, press eject, note down how many lights are flashing. Do that a total of 4 times. That's your secondary error code.

 

[Martin C]

i cant see any error code
sorry the 2 redlights are not 1&2 its 1&3 as the below image

http://www.imageuploading.net/images/14184/2-red-lights

http://bit.ly/wLGljN

 

[mechgamer123]

I had the same problem with my console. Try rebuilding the image with 360 multibuilder and make sure you flash with a hardware nand flasher, not rawflash.

Sent from my Galaxy Nexus using Tapatalk

 

[ARUNCREATIONS]

Hai Martin

Thanks for ur help..
i got the secondray error code..0013 ( ram overheating)
i also write the 14699 build image with rawflash v3

What to do now?

 

[Martin C]

So I really don't think it's RAM overheating TBH as I'm sure that you'd get this when booting to XeLL too.

Try writing with nandpro instead.

 

[ARUNCREATIONS]

I will write buildimage as said by mechgamer123 and write through nandpro and post results soon..Thanks martin and mechgamer123

 

[oO Elite Oo]

I believe Martin C made a good point about NOT grabbing the mother from the Heat Sink when removing the mobo from the metal cage.