3 Zepher's won't glitch

D

djob1981

Full Member
Dec 5, 2011
39
0
i have 3 sephers that i have dumped the nand using jtag tool created eec and flashed the nand back fine no problems.

I have installed the coolrunner with no problems and even get the coolrunner to flash green every 5 seconds which should indicate that it is trying to glitch and that the cables are right but it wont glitch no matter what i try.

I have attached photos of one of the installs
 
A

Anobix

Full Member
Nov 15, 2010
49
0
USA
I followed those same steps, Mickey and didn't have any luck getting my Zephyr to glitch, re-routed cables/wires etc and no XeLL on two different screens+cables (same problem as the OP). I just RGHed a slim and it worked flawlessly. I think you may just have a magic touch :)
 
M

Mickey3177

VIP Member
Feb 2, 2011
301
0
Las Vegas USA
The steps I used in that thread worked for me and I see your not using QSB I always do, that could make a difference. What is the CB on these?, mine were 4578 and did you flash to 13604 dash before reading your nand? just some ideas, it's strange that you have all 3 that don't glitch and I have 3 that do :confused:
 
M

Mickey3177

VIP Member
Feb 2, 2011
301
0
Las Vegas USA
If you load your nand into 360 Flash Tool, it will give you all the info on your nand, I always update my dash to 13604 BEFORE I do anything, then read your nand.
 
D

djob1981

Full Member
Dec 5, 2011
39
0
My CB is 4578

---------- Post added at 08:41 ---------- Previous post was at 08:39 ----------

going to update the dash and see if that helps
 
I

ishockin

VIP Member
Feb 4, 2011
275
23
Ohio
Martin c has stated that it is not necessary to update the dashboard where he had done slims on 9199 and they glitch fine
 
D

djob1981

Full Member
Dec 5, 2011
39
0
Ok so i flashed the stock nand back and updated as per the guide to 13604. then dumped the nand twice with no bad blocks wrote back the image_00000000.eec file reinstalled coolrunner solid red light on. Turned on the xbox with cr on Norm mode and switch set to PHAT, green light flashed but no glitch
 
D

djob1981

Full Member
Dec 5, 2011
39
0
one thing that i have noticed is that my xbox does not sound like it is restarting? hope this helps as i am getting frustrated now
 
N

N.E.Modz

VIP Member
Sep 27, 2009
2,285
68
A.K.A daleh43
djob1981 said:
Ok so i flashed the stock nand back and updated as per the guide to 13604. then dumped the nand twice with no bad blocks wrote back the image_00000000.eec file reinstalled coolrunner solid red light on. Turned on the xbox with cr on Norm mode and switch set to PHAT, green light flashed but no glitch
Click to expand...
you connecting via AV cable or HDMI ?

dale;)
 
D

djob1981

Full Member
Dec 5, 2011
39
0
Quick update i have reflashed orig nand back booted no problems, re dumped nand 3 times checked it and created gitch file .ecc rewired in coolrunner and reprogrammed it for my board
It is back at the same stage again wont boot to xell just keeps on flashing the green light on coolrunner board every 5 seconds.

Really scratching my head now
 
voojoo

voojoo

Senior Member
Nov 25, 2010
141
18
have you ever success glitched just 1 Xbox ? Sorry to ask you like this but if you never do glitch before try to do different method. let's say.. Swith on Cool runner to normal then write ecc image or write image with JTAG tool. just an idea.
 
D

djob1981

Full Member
Dec 5, 2011
39
0
voojoo said:
have you ever success glitched just 1 Xbox ? Sorry to ask you like this but if you never do glitch before try to do different method. let's say.. Swith on Cool runner to normal then write ecc image or write image with JTAG tool. just an idea.
Click to expand...
I have only tried on these 3 zephyr boards so far, i have tried to write to the nand with and without coolrunner attatched with cool runner on nor and also on prog, i have used miltibuild tool v4 and also jtag tool neither help me to get it to glitch
i have just ordered some new flux and QSB as i am currently doing this with just wires
 
You must log in or register to reply here.