ANSWERED 74 bad blocks possible to remap in trinity nand?
- Thread starter Eazywolf
- Start date
Martin C
VIP Member
Do the same again, but note which blocks are non-matching.
See if you have the same non-matching blocks.
See if you have the same non-matching blocks.
Martin C
VIP Member
Martin C
VIP Member
Martin C
VIP Member
Can you take a hi-res picture of your NAND?
I want to make sure there's nothing bridged on any of the pins.
Do you get any errors when dumping the NAND?
EDIT: just to be sure, you're NOT comparing these dumps to your original are you?
you should be comparing them to each other.
I want to make sure there's nothing bridged on any of the pins.
Do you get any errors when dumping the NAND?
EDIT: just to be sure, you're NOT comparing these dumps to your original are you?
you should be comparing them to each other.
Last edited:
I dont sure, i understand the question exactly, but i try to answer.
I'am sure i do all needed comparing. I compare all dumps with each other and compare all dumps with other older dumps (original).
I compare everything with everything very many times. With same results
Here is the best success hi-res pictures from nand.
I'am sure i do all needed comparing. I compare all dumps with each other and compare all dumps with other older dumps (original).
I compare everything with everything very many times. With same results
Here is the best success hi-res pictures from nand.
Martin C
VIP Member
ok - flash your original dump to your console:
nandpro usb: -w16 nand.bin (whatever you called it).
then read it back:
nandpro usb: -r16 compare.bin.
then compare the two in xnandhealer.
nandpro usb: -w16 nand.bin (whatever you called it).
then read it back:
nandpro usb: -r16 compare.bin.
then compare the two in xnandhealer.
I am done with all. It look likes good, but i can't open the file: compare.bin from xnand healer read tab, i just renamed it to nand1.bin and after that the xnand healer opened it correctly.
!! It is much with the original nand!!
!! After this i tried the jtag tool compersation, but same result, files are much!!
May i on the good way?
What is the difference -w and +w command?
!! It is much with the original nand!!
!! After this i tried the jtag tool compersation, but same result, files are much!!
May i on the good way?
What is the difference -w and +w command?
My consol still do not working. Leds are spinning and glowing and spinning and glowing and finely center green light, but black screen on television 
My south bridge is very hot.
My south bridge is very hot.
Last edited:
Martin C
VIP Member
ok so the original error was you were comparing a NAND *after* a change was made, which is why it never matched.
I think you need to boot to XeLL now and confirm your LDV.
nandpro commands
-w - write raw file
+w - write raw file but build new ECC data.
I think you need to boot to XeLL now and confirm your LDV.
nandpro commands
-w - write raw file
+w - write raw file but build new ECC data.
Xell dont boot. I dont understand why, i do everything like before, but no success.
Only the red led light on coolrunner, but the green led start on the coolrunner when i push the eject button on xbox360, and it starts blinking various times.
Sometimes blink 8 times, sometimes blink 3 times, absolutely random.
But the end all time is the same, the center green led on the consol front, stops the continuous light approximately half or quarter second, when the green led on coolrunner blinks last time.
After that, the red led work on the coolrunner, the green dont, but the green center led on the xbox face is light, but nothing on hdmi.
I tried rewrite the xell to nand, dont work, i tried to generate a new ecc file and write to the nand, dont work. I see and check the soldering points on mainboard and on coolrunner, but everything looks like and sounds like done, but it is only a big and expensive bullshit with green and red led and power button.
What more do i have to do?
Only the red led light on coolrunner, but the green led start on the coolrunner when i push the eject button on xbox360, and it starts blinking various times.
Sometimes blink 8 times, sometimes blink 3 times, absolutely random.
But the end all time is the same, the center green led on the consol front, stops the continuous light approximately half or quarter second, when the green led on coolrunner blinks last time.
After that, the red led work on the coolrunner, the green dont, but the green center led on the xbox face is light, but nothing on hdmi.
I tried rewrite the xell to nand, dont work, i tried to generate a new ecc file and write to the nand, dont work. I see and check the soldering points on mainboard and on coolrunner, but everything looks like and sounds like done, but it is only a big and expensive bullshit with green and red led and power button.
What more do i have to do?
Martin C
VIP Member
ok - try an AV cable instead of HDMI.
If you're doing this without a DVD drive connected, you'll know when your console has glitched when:
1. The front light on the slim stops flashing.
2. The optical output port on the back is active (you'll see the red coming from it).
3. Any USB device connected is active.
If all three of these are happening, then it's glitched. If there's no picture you have a bigger issue.
If you're doing this without a DVD drive connected, you'll know when your console has glitched when:
1. The front light on the slim stops flashing.
2. The optical output port on the back is active (you'll see the red coming from it).
3. Any USB device connected is active.
If all three of these are happening, then it's glitched. If there's no picture you have a bigger issue.
On av cable, the xell is boot with and without optical drive, but i dont know what is the next step to use my consol with hdmi and all ok.
( optical audio output dont work)
You said may i need to check the ldv, i checked the topic in your signature, you wrote this problem comes with 3 red lights and 0022.
I have never had the same error. I have two " f " from fuse line 7 to cpu key.
I need to write ldv count to options_r.ini anyway or not?
I worried about the 13599 dash version, and the dont working hdmi.
Which tool i need to use to generate image for this dash? Or it is not important?
The hdmi issue are brutal big trouble with need reballing with rework station or i can fix it likely?
( optical audio output dont work)
You said may i need to check the ldv, i checked the topic in your signature, you wrote this problem comes with 3 red lights and 0022.
I have never had the same error. I have two " f " from fuse line 7 to cpu key.
I need to write ldv count to options_r.ini anyway or not?
I worried about the 13599 dash version, and the dont working hdmi.
Which tool i need to use to generate image for this dash? Or it is not important?
The hdmi issue are brutal big trouble with need reballing with rework station or i can fix it likely?
alexhore
BANNED
Boot xell and look at the list of fuseset data. On lines 07 and/or 08 you will see a bunch of ffffs.
Count them eg....
http://imageshack.us/photo/my-images/42/dsc05924trollololol.jpg/
LDV = 11
Edit, Just re-read your post yes you need to set ldv count to 2 in options_r.ini.
Last edited:
Martin C
VIP Member