After new install of R-jtag on a felcon E79 help !

Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
I think you're at the point where I'd get someone to give it the once over for you. Everything looks to be in place but you're missing something.

Since you can boot without a DVD drive, the firmware version on BenQ is totally irrelevant.
 
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
Didn't think it the Ben-q had anything to do with it . I know I'm right there ... I'm getting a green light flashing on the board and a red that stays on . I was looking in my log files for j-runner and did not see the log over there .


Sent from my iPhone using Tapatalk
 
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
I do have it set to 1-3. It looks exactly like it .

Same board settings except for the switch is set to on

Sent from my iPhone using Tapatalk
 
Last edited:
keil423

keil423

VIP Member
Apr 4, 2011
1,954
88
South Dakota, USA
www.epicconsole.com
Try setting the aud clamp to the 0 value and go threw all the dips one at a time ( except 8 and leave 7 on). If your still not having luck then try again with 330 and again after that with the 480. After trying all three of those if you still haven't had luck then you go back to square one but add a voltage jumper. Keep at it and you'll get it.

I personally don't feel that you need to send it off to anyone. Your soldering looks clean which is unusual to see in help threads these days kudos for that! Also thanks for actually posting good images of the install.
 
  • Like
Reactions: Magicherbz
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
keil423 said:
Try setting the aud clamp to the 0 value and go threw all the dips one at a time ( except 8 and leave 7 on). If your still not having luck then try again with 330 and again after that with the 480. After trying all three of those if you still haven't had luck then you go back to square one but add a voltage jumper. Keep at it and you'll get it.

I personally don't feel that you need to send it off to anyone. Your soldering looks clean which is unusual to see in help threads these days kudos for that! Also thanks for actually posting good images of the install.
Click to expand...
Thanks man I will try it now , I notecard something , when I plug in the power and aux the green light on the front never blinks like it should when u have the DVD disconnected . It's just soled green . ???


Sent from my iPhone using Tapatalk
 
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
Magicherbz said:
Thanks man I will try it now , I notecard something , when I plug in the power and aux the green light on the front never blinks like it should when u have the DVD disconnected . It's just soled green . ???


Sent from my iPhone using Tapatalk
Click to expand...
Now when mean setting the aud clamp to the 0 do u mean Desoldering it ?"the cable " ?


Sent from my iPhone using Tapatalk
 
Last edited:
keil423

keil423

VIP Member
Apr 4, 2011
1,954
88
South Dakota, USA
www.epicconsole.com
No I mean just to flip the switch to 0. I'm referring to the three way switch. The wire is actually the aud clamp.

It looks to me like you have everything soldered correctly so other then trying the different voltage jumpers or trying without aud clamp you should be about done with the iron. It's just a matter of flipping switches for the most part.

Try removing the voltage jumper and set the aud clamp three way switch to 0. Let me know it your green light starts flashing again and be sure to run rater and post your logs again
 
  • Like
Reactions: Magicherbz
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
keil423 said:
No I mean just to flip the switch to 0. I'm referring to the three way switch. The wire is actually the aud clamp.

It looks to me like you have everything soldered correctly so other then trying the different voltage jumpers or trying without aud clamp you should be about done with the iron. It's just a matter of flipping switches for the most part.

Try removing the voltage jumper and set the aud clamp three way switch to 0. Let me know it your green light starts flashing again and be sure to run rater and post your logs again
Click to expand...
The green light in the front is solid and the one on the rjtag board I'd flashing every 4 secs , the red one is solid . I'm going to try it now give me 3 mins


Sent from my iPhone using Tapatalk
 
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
===================================================
Tuesday, December 10, 2013 12:09:59 AM
J-Runner v0.3 Beta (4) Started

WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button

Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Falcon/Opus
Jtag Selected
Nand Initialization Finished
Aud_Clamp Selected
XeLL file created Successfully falcon_hack_aud_clamp.bin
 
G

gavin_darkglide

VIP Member
Dec 14, 2012
2,303
118
If you are getting e79 then the system has successfully glitched. your problem is with the jtag wiring. so put the r-jtag settings back to where it got e79, then try changing the jumper and 3 way switch. If it still doesnt work test TMS/TDI with a multimeter. They should be around 1.5Kohms. If you arent getting values like this reflow/reball the gpu.

Also make sure the stock nand still boots, if you havnt already, flash back stock and remove postout, or 5V wires from r-jtag and make sure it boots.

And TMS/TDI are not used by the stock nand, so if these values dont equal around 1.5kohm and still boots stock that is why. and when testing make sure to turn off jtag wiring. So turn off 2 way switch, and set 3 way switch to 0-off.
 
Last edited:
  • Like
Reactions: Magicherbz
M

Magicherbz

Full Member
Jun 21, 2012
48
0
Usa
gavin_darkglide said:
If you are getting e79 then the system has successfully glitched. your problem is with the jtag wiring. so put the r-jtag settings back to where it got e79, then try changing the jumper and 3 way switch. If it still doesnt work test TMS/TDI with a multimeter. They should be around 1.5Kohms. If you arent getting values like this reflow/reball the gpu. Also make sure the stock nand still boots, if you havnt already, flash back stock and remove postout, or 5V wires from r-jtag and make sure it boots.
Click to expand...
So I have tested all those setting with the multimeter and was getting 1.56 on each of them , I will try doing what you said . Thanks for your input ;)


Sent from my iPhone using Tapatalk
 
You must log in or register to reply here.