Console Type: Jasper
NAND size: 256
Dashboard version: e.g 2.0.13599
CB version: ?
Screenshot of NAND details from J-Runner: None
(attach an image to your post)
J-Runner log:
POST output from J-Runner (either POST_OUT monitor or RATER output):
(2 cycles is enough)
updflash.bin log (if applicable):
Image of R-JTAG board(blue cable and ribbon has been removed on the picture):
https://dl.dropboxusercontent.com/u/53726931/R-JTAG SolderSide.jpg
https://dl.dropboxusercontent.com/u/53726931/R-JTAG Part Side.jpg
Images of close-up soldering to motherboard:
(attach images to your post)
Pictures High Qual.
https://dl.dropboxusercontent.com/u/53726931/R-Jtag%203RROD%20Error%200010%20Low.pdf]Pictures Low Qual.[/url]
Description of problem:
Installed the Ultimate kit. And got the 3RROD error 0010. The board doesn't do anything beside blinking 3 red lights.
It's installed by the guide on the forum. Dip 4, 7, 8. Aud_clamp on, 470ohm
The Xbox will not boot with the J-Runner not installed either.
Tried both RST points.
Tried 2 different JRP2 boards
Has ohmed all the solderpoints that I could get to on both sides. (all short fine)
Could the too early dash be a problem ? And shouldn't boot to it with the QSB's on and J-Runner off ? Really don't wanna remove the QSB's to make a Dash Update
Was the console working before you started: Yes (A XBOX with the drive flashed)
Thanks in advance, hope it's enough information.
NAND size: 256
Dashboard version: e.g 2.0.13599
CB version: ?
Screenshot of NAND details from J-Runner: None
(attach an image to your post)
J-Runner log:
Code:
[B][B][B][B][B][B]26. oktober 2013 00:05:35
[/B][/B][/B][/B][/B][/B]
Code:
J-Runner v0.3 Beta (2) Started
Checking Files
Finished Checking Files
Checking Console..
Version: 00
Wrong Version.
Can not continue
Checking Console..
Version: 00
Wrong Version.
Can not continue
Load Files Initiliazation Finished
15574
Couldn't add dashlaunch patches to C:\Users\mickkirkegaardnielse\Desktop\JTAG-RGH\J-Runner\xeBuild\15574\_glitch2m.ini
Started Updating Console to 15574
---------------------------------------------------------------
xeBuild v1.09.639
---------------------------------------------------------------
base path changed to C:\Users\mickkirkegaardnielse\Desktop\JTAG-RGH\J-Runner\xeBuild
---- { Update Mode } ----
***** WARNING: reusing folder C:\Users\mickkirkegaardnielse\Desktop\JTAG-RGH\J-Runner\output\!
started, watching network for xbox...UDP wait timeout!
failed to find xbox beacon
***** FATAL UPDATE ERROR: unable to find console!
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
[B][B][B][B][B][B]---------------------------------------------------------------
[/B][/B][/B][/B][/B][/B](2 cycles is enough)
updflash.bin log (if applicable):
Image of R-JTAG board(blue cable and ribbon has been removed on the picture):
https://dl.dropboxusercontent.com/u/53726931/R-JTAG SolderSide.jpg
https://dl.dropboxusercontent.com/u/53726931/R-JTAG Part Side.jpg
Images of close-up soldering to motherboard:
(attach images to your post)
Pictures High Qual.
https://dl.dropboxusercontent.com/u/53726931/R-Jtag%203RROD%20Error%200010%20Low.pdf]Pictures Low Qual.[/url]
Description of problem:
Installed the Ultimate kit. And got the 3RROD error 0010. The board doesn't do anything beside blinking 3 red lights.
It's installed by the guide on the forum. Dip 4, 7, 8. Aud_clamp on, 470ohm
The Xbox will not boot with the J-Runner not installed either.
Tried both RST points.
Tried 2 different JRP2 boards
Has ohmed all the solderpoints that I could get to on both sides. (all short fine)
Could the too early dash be a problem ? And shouldn't boot to it with the QSB's on and J-Runner off ? Really don't wanna remove the QSB's to make a Dash Update
Was the console working before you started: Yes (A XBOX with the drive flashed)
Thanks in advance, hope it's enough information.
Last edited:
