after testing cr3 pro and slim proto v2 to RGH xbox red light

[gojo84]

I think I mes up my xbox
i started with cr3 pro ,trinity qsb v3 and qsb slim post v2
1 read 4 time my nand and saved nand 2,3,4 cause the first one was used to create the cell
2 create ECC
3 write my ECC
4 tried to boot and the cr3 pro had a red light constant and a green light flashing 3-4 secs
5 tried several tune up configs but nothing
then desoldered the cr3 nad installed the slim proto v2 with slim post qsb v3 and done the the exact steps like cr3 pro but with slim proto no green light and no glitches time in cr3 rater
I desolder every thing and tried to boot with stock but nothing the xbox starts up with just only a red light ,flashed the nand I stored from the 4 reads of the original of the starting process but still the same ,please what should I do buy a new xbox and started over cause I'm decided to RGH a trinity on cost to destroy till I accomplished what I started or there is still hope for this crappy one ?

 

[JrMods]

Its possible that something was damaged when you tried to solder the chips onto the motherboard. If you post pictures of the motherboard it would help pick out anything that looks irregular/what is causing the red dot.

 

[tomma66]

You need to fill in the template http://team-xecuter.com/forums/showthread.php?t=96474.

 

[gojo84]

 

[gojo84]

sorry
my log of JR
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9188
Trinity

 

[gojo84]

View attachment 26805View attachment 26804

- - - Updated - - -

these are the photos af my back board

 

[jsinger47]

yeah, you ripped off the CPU_RST point. You'll need to re-trace that before it will work.

 

[gojo84]

if there a possibility to solder its done but what do I solder could you please show a diagram of the soldering ?

 

[ablegepu]

i cant see the pictures of your cpu_rst but here you go...




the topside point is here

(i modified on of these images the other is from bga mods i think)

 

[gojo84]

MANY THAANKS ,no I 've not ripped out the FT4R2 so I'll solder that trace but I realise that I've got none possibilities to solder qsb post anymore
thanks again

 

[gojo84]

hi again I just solder in two different points of the trace , 1 to end of trance on the pad and the other as now in the picture and nothing red light again

 

[ablegepu]

check for continuity between topside resistor r4d4 and the trace where you soldered to

 

[gojo84]

thanks for reply but I think I have nand issues and maybe got write the nand after created ECC image with cr3 pro write it and then rewrite it with slim proto v2 and here I think I [email protected]%$ck it up

 

[Martin C]

That wouldn't cause the problem you're seeing. How long does it take to show a red light?

 

[gojo84]

at instant that i power on

 

[gojo84]

I said nand issues cause after I got probs with booting cr3 pro full post and installed slim proto I directly flashed my nunddump of the first reads that I saved of my original nand

 

[gojo84]

martin I'm reading around the forum and I think that only you can resolve this issue ,I already got another trinity and I'm preparing to start over RGH but I cant left this one unsolved cause I love too much
configure where was the trouble and if its possible solve the repairing not as much for the money I lost cause I'll be not surrended in 3-4 rrod consoles but for my own ego
I'm not new in mods so do I open a new tread with your help cause there are tons of new user that need guide from the beginning in how must be configured J-RUNNER ,what to download what are correct settings of the j-runner program
AND FOR LAST THING ,I JUST WANT TO RETRIEVE THE DVD KEY TO BE ABLE TO FLASH TO TX LTU2 BOARD AND RETURN THE CONSOLE BACK TO STOCK AND USE THE CONSOLE AS THE PHATS ONE WITH BURNED DVDS


PLEASE PROVIDE USEFUL HELP

 

[ablegepu]

If you flashed back to stock it should work but cpu-rst needs to be right first check the points I told you for continuity if your multimeter does not beep then you need to solder to r4d4 instead of the ft4r2 I can't tell in the image if it is good or not but its easy to disconnect the trace from the pad by accident. The best advice ANYONE can give you is send it to a pro It CAN still be fixed and rgh'd trust me you don't want to start on another console because you haven't read enough yet. You learn from your mistakes but if you have not learned anything yet don't make another one.

 

[gojo84]

I double checked for that beep before I post that I have nand issues