alt code 0010 2 days after nand x install

[cilo456]

did the rrod x clamp repair and its still doing it

3 red lights if i take out the dvd drive xell boots and after put the drive back in works fine

launch xexmenu
and it hangs on black screen
turn off and on again and 3 red lights again

 

[optantic]

E05: CPU over heating - If you are receiving this error after disassembling your console make sure to all 8 of the heatsinc screws are tightened securely to the board/heatsink holes.

have you apply new thermal paste to the cpu???

 

[Xmods]

0010 is southbridge or a shorted wire in your jtag wiring id say it's jtag short since it was working for 2 days double check your jtag wiring

 

[cilo456]

ok thanx and another question do i ned to keep the wires connected taht connect to the nand x

 

[syst3merror]

ok thanx and another question do i ned to keep the wires connected taht connect to the nand x

technically once you dump the nand and you jtag the console, you can remove the nand-x wiring and keep JUST the jtag wiring

 

[cilo456]

ok another thing when i read the nand i did it 2x compared the same

then i made the freeboot image and clicked write and ys i input my cpu key

when i wrote freeboot i thought it would boot to the dash but didnt it went to xell and i thought i did something wrong so i read and create image again and write freboot

then i kicked myself in the ass and thoughtmaybe if i plugin the DVD DRIVE it wll boot and it did

so what i'm asking is sould i rewrite my orig nand dump with freeboot or am i good

well i did that and still 3 red lights alt code 0010 desoldered and resoldered 5x already not doing it anymore i know its good i'm lost

 

[cilo456]

would it be the jumper settings and the switch

 

[cilo456]

ok i reflashed orig nand and turnd off jtag that means its the xbox not my work right

but what is wrong with it i did the rrod fix andused a little more the usual arctic silver

 

[cilo456]

now its rrod all the time nothing turns on but the 3 red lights fans dont spin nothing doesnt even get hot if i leave it on for a hour

 

[Xmods]

did this all start after you did you rrod mod ?

 

[cilo456]

no i did the rrod mod because of it

 

[cilo456]

it used to do it once in a while now its always rrod i can still read and write to the nand

 

[cilo456]

i think that it is a short cuz nothing is powered when i turn it on adn the same thing happened when i repaired the traces cuts on one of my 9 series lite ons

i tihnk it just might be giving the wrong code 0010

i dont know just a thought ive tried resoldering over and over again

 

[cilo456]

the best pic i could take the close up option doesnt work on my camera

i dont know i think i did a good job for my first time soldering

 

[cilo456]

another update
i let it sit all night and just turned it on and got 1 red light and e79 error

i reflashed orig nand and tried and back to 3

and another funny thing i forgot to mention is if i keep it plugged in and not turned on it turns on by itself funny

 

[cilo456]

ok looks like i'm getting 1 red light e 79 now all the time

i think the 3 red r done now i hope so

 

[cilo456]

ok i got everything back to normal

now to make sure is there anything special i do to to a xenon with dash 6xxxx the blades

 

[cilo456]

so do i need the xenon e79 error jtag install kit? anyone

 

[cilo456]

i bought the e79 kit installed and the same sh*t

i can get it to boot if i leave it for a few hours then rrod with no error alt error 0010

 

[iLuuKe]

try using the normal xenon jtag wiring......its only 3 simple wires ad its easier to install

hope i helpped