Another 'could not detect' thread

Status
Not open for further replies.
O

OilyD

Full Member
Dec 26, 2010
70
0
In my man shed
I've already posted here
:http://www.team-xecuter.com/forums/showpost.php?p=469029&postcount=195
But thought I'd try here as well as it seems a bit more active :wink:

This is my first jtag install which hasn't gone smoothly!
I've installed my Nand x pin headers and the jtag qsb's on my Xenon.I've read my nand a few times and compared 2,both with 0 non-matching block(s) found.
Preceded to write Xell which it did,un-hooked everything,booted it up to get the cpu key and got 3 red flashing led's.
Powered it down and tried to write back the original nand and now it's saying it could not detect flash controller.I've tried un-installing/fresh install of the Nand X,resetting the Nand X,restarting the pc etc.
The lights are on but nobodys home :wink:
I've double checked all my soldering points,all good,(if I do say so myself:tongue:,don't have a camera to post pics yet,only Iphone 3g)
On a side note,could I have gotten 3 good nand dumps with poor soldering connections?
So I'm stuck with a mother board that won't boot up and a nand x that now can't be detected :(

Were do I go from here :confused:

Any help greatly appreciated :cool2:
 
O

OilyD

Full Member
Dec 26, 2010
70
0
In my man shed
XxLittleTxX said:
I'd lay it down to a bridge or poor connection. Pics would help try with your phone and we will do our best.
Click to expand...
The ipone3g doesn't take close up pics to well!!
I'll see what I can do though

---------- Post added at 17:48 ---------- Previous post was at 17:46 ----------
XxLittleTxX said:
You say your using pin headers take those out and go qsb or direct wires pin headers are the hardest for beginners
Click to expand...
Wouldn't exactly call myself a 'beginner' when it comes to soldering :biggrin:
 
W

WestCoastConsoles

VIP Member
Dec 29, 2010
1,339
0
Portland, OR
OilyD said:
The ipone3g doesn't take close up pics to well!!
I'll see what I can do though

---------- Post added at 17:48 ---------- Previous post was at 17:46 ----------



Wouldn't exactly call myself a 'beginner' when it comes to soldering :biggrin:
Click to expand...
Wasn't trying to insinuate begginer at soldering but first time jtagger. My apologies if it came off that way.
 
O

OilyD

Full Member
Dec 26, 2010
70
0
In my man shed
XxLittleTxX said:
Wasn't trying to insinuate begginer at soldering but first time jtagger. My apologies if it came off that way.
Click to expand...
No offence taken mate
I appreciate all the help I can get help so keep the replies coming,anything you can think of,post up

---------- Post added at 17:59 ---------- Previous post was at 17:57 ----------
banjaxt said:
what i do with the pinheaders is using a 0.8mm drill head drill through the points, and they are already tinned. just a dab of solder ;)
Click to expand...
I used my solder sucker but I'll bear that in mind the next time(if there is one :wink: )
 
O

OilyD

Full Member
Dec 26, 2010
70
0
In my man shed
Managed to dig out the camera,kids broke it some while a go,doesn't focus to good :frown:
Jtag qsb's


Pin headers from underneath



Anything look out of the ordinary here?
 
Status
Not open for further replies.