LITEON 0225 Bad flash (Help Please)

B

BHL ADDZ

Full Member
Jan 21, 2010
73
8
This is as far as I can get with it, it won't let me erase.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

JungleFlasher 0.1.92 Beta (304)

Session Started Thu Feb 02 19:04:58 2012



This is a 32 bit process running on a 32 bit CPU

portio32.sys Driver Installed

portio32.sys Driver Started, thanks Schtrom !

Found 2 I/O Ports.

Found 2 Com Ports.

Found 4 windows drives A: C: D: E:

Found 1 CD/DVD drives D:



XECUTER X360USB PRO attached.





Getting Status from port 0x9000

Invalid Status 0x0



Getting Status from port 0x9000

Invalid Status 0x0

Sending Vendor Intro to port 0x9000

Status 0x80

Re-sending Vendor Intro:

.................

Serial flash found with Status 0x72



Sending Device ID request to port 0x9000

Spi Status: 0x9C

Manufacturer ID: 0xC2

Device ID: 0x11

Flash Name: MXIC(MX25L2005)

Flash Size: 262144 bytes

---------- Post added at 19:09 ---------- Previous post was at 19:06 ----------
joesinger47 said:
what SPI status does the drive show?

if 0x00, try erasing first (button next to read/write)
Click to expand...
Where it normally shows the SPI it's blank!!
 
jsinger47

jsinger47

Troll Eating Dogs
Feb 6, 2011
8,133
128
Grand Rapids, MI
well at this point, i would suggest re-locking the spi, then re-unlocking

however, re-unlocking is going to be a chore as you no longer have a spot to probe/solder sputnik to with GND + 10ohm resistor

the command to re-lock the spi when you can't do it through GUI is "ctrl + shft + f11"
 
  • Like
Reactions: BHL ADDZ
B

BHL ADDZ

Full Member
Jan 21, 2010
73
8
joesinger47 said:
well at this point, i would suggest re-locking the spi, then re-unlocking

however, re-unlocking is going to be a chore as you no longer have a spot to probe/solder sputnik to with GND + 10ohm resistor

the command to re-lock the spi when you can't do it through GUI is "ctrl + shft + f11"
Click to expand...
That's where I think I went wrong it wasn't fully unlocked and it let me flash, I wonder if there is alternative point to the one I lost!

Thanks for your time BTW, much appreciated.
 
B

BHL ADDZ

Full Member
Jan 21, 2010
73
8
I'm about to solder the alternative point to the chip (fingers crossed), I locked it again but the button still doesn't show!

Here is the log:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

JungleFlasher 0.1.92 Beta (304)

Session Started Fri Feb 03 09:23:32 2012



This is a 32 bit process running on 3 x 32 bit CPUs

X360USB PRO detected, Version 0.18



Found 1 I/O Ports.

Found 0 Com Ports.

Found 5 windows drives C: D: E: F: G:

Found 1 CD/DVD drives E:



Sending Vendor Intro to port 0x0000

Status 0x80

Re-sending Vendor Intro:

................

Serial flash found with Status 0x72



Sending Device ID request to port 0x0000

Spi Status: 0x9C

Manufacturer ID: 0xC2

Device ID: 0x11

Flash Name: MXIC(MX25L2005)

Flash Size: 262144 bytes

Loading firmware file C:\Users\ADDZ\Desktop\0225 Chip Unlock\Dummy.bin

MD5 hash: 69e03ce685f770cb8d6a07da22806b0e

Inquiry string found

Identify string found

Drive key @ 0xA030 E08E7119AB5EBC959529D37C668CAD29

Firmware Osig: [PLDS DG-16D4S 0225]

Firmware is: SlimKey Extract

Auto-Loading firmware file C:\Users\ADDZ\Desktop\JungleFlasher v0.1.92 Beta (304)\firmware\LTPlus-0225-v3.0.bin

MD5 hash: 1a38d3a2a6519339599fa1866642c513

Genuine LT plus v3.0

Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

Firmware Osig: [PLDS DG-16D4S 0225]

Firmware is: LT-Plus 3.0

Spoofing Target

DVD Key copied to target

Key Sector copied from Source to Target

Target is LT - ID strings not copied to Target



Spi Status: 0x8C



Getting Status from port 0x0000

SPi flash found with Status 0x72



Sending Chip Erase to Port 0x0000

Writing target buffer to flash

Writing Bank 0: .
Click to expand...
Not sure where I go from here but I'll try get the chip on now.
 
B

BHL ADDZ

Full Member
Jan 21, 2010
73
8


Got the SPI button to show up, where do I go from here? (just want to make sure I do it right in case the button doesn't show up again if I do it wrong!)
 
B

BHL ADDZ

Full Member
Jan 21, 2010
73
8
noobnotforlong said:
It does show at the bottom of you jf log SPI 0x8c

Sent from my HTC Desire Z using Tapatalk
Click to expand...
Spi Status: 0x8C was when I pressed Ctrl, Shift & F11 but I soldered the Spudnik chip back on and the SPI button comes up as 0x00 now, not sure what to do, just flash it or hit the SPI 0x00 button?

The switch has been at normal all along too.
 
B

BHL ADDZ

Full Member
Jan 21, 2010
73
8
I can get it to write but it doesn't verify, the switch is set to normal and I haven't moved it.

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
............
Flash Verification Test !
Reading Bank 0: Dump Failed
Click to expand...
 
N

noobnotforlong

Senior Member
Jan 31, 2012
116
0
Rotherham
This is due to it still been locled

Lock the drive by ctr shift f10/11 I don't recall

Then outro

Intro again

Click the 0x8c button
Then touch the 10ohm to gnd from the point your using I am guessing a pin on the chip as you have damage your trace

Then once you here the beeps remove resistor and proceed your flash or erase whatever tickled your fancy

Sent from my HTC Desire Z using Tapatalk
 
Last edited:
  • Like
Reactions: BHL ADDZ
B

BHL ADDZ

Full Member
Jan 21, 2010
73
8
I've give up on it, the SPI button doesn't show unless I move the switch to unlock then it gives me 0x00 I then switch to normal and lock it to 0x8c, after that I try the unlock but no beeps at all!

When I just go ahead and try to write it either stops at the 1st dot or it will write but not verify :(

Thanks for your time everyone that halped.
 
You must log in or register to reply here.