- Nov 6, 2013
- 150
- 0
So I have a extra r-jtag chip and if I flash it with jrunner as a coolrunner rgh chip will it work
Can I flash my R-jtag chip into coolruner glitch chip?
- Thread starter teknogod17
- Start date
chase
VIP Member
BL4K3Y
VIP Member
Even if the R-JTAG code was public, what makes you think writing something else to it will fix your problem?
The issue you're having is related to a poor install (the most likely cause) or a faulty console (RROD on the retail NAND).
I have done around 20 R-JTAG installs on various boards (Falcon, Jasper and Zephyr) and I haven't had a single issue.
Last edited:
chase
VIP Member
most people with your status on the forum would claim hundreds of installs.. heck, I've seen some noobs claim installs by the hundreds .. gotta love the honesty
BL4K3Y
VIP Member
I've done far more CoolRunner installs, but my point to the OP was that when the hardware is installed and configured correctly, everything works as it should.most people with your status on the forum would claim hundreds of installs.. heck, I've seen some noobs claim installs by the hundreds .. gotta love the honesty
I have fixed countless countless installs caused by people who either can't solder and think an XBOX 360 is the best place to start or by those who don't (or usually won't) follow the instructions and guides we provide.
Let's be honest - the guides are written to cater for beginners and pros alike, but we can't please everyone
.
Last edited:
- Nov 6, 2013
- 150
- 0
this has nothing to do with the previos thread I have another r-jtag chip aside from the one im using in my jasper I want to rgh my slim thats why im asking this qestion
chase
VIP Member
keep the r-jtag for another phat console .. or you can sell or trade it
for the slim, you should get the slim proto2 .. coming soon
for the slim, you should get the slim proto2 .. coming soon
- Nov 6, 2013
- 150
- 0
also I think the issiu is the not using the aud clamp qsb and doing wire install and using wrong resisters
chase
VIP Member
- Nov 6, 2013
- 150
- 0
I do fallow guides correctly I just miss some of the little things which is a big problem. I'm also using a pretty bad solder iron with a tip that smels bad and turned solder black and gets so hot it glows orange
with my old solder iron I did good see here was my last r-jtag install on my friends xbox
with my old solder iron I did good see here was my last r-jtag install on my friends xbox
- Nov 6, 2013
- 150
- 0
see my install with my good solder iron a few months back
- - - Updated - - -
see my install with my good solder iron a few months back
- - - Updated - - -
see my install with my good solder iron a few months back
Attachments
xzanox
VIP Member
- Mar 1, 2010
- 3,346
- 128
xzanox - I don't come and slap the cocks out of your mothers mouth when she's at work, do I ?
xzanox
VIP Member
Antalpromille
VIP Member
If you know your problems why not do something about them? Read more carefully and get better soldering equipment, and if we never hear anything about problems from your side again we know that it actually was the problem.
- Nov 6, 2013
- 150
- 0
Ile be willing to trade it the only prob is that its just the chip no qsbs or wires just glitch chip I would be willing to trade for coolrunner rev c no wires.
- Nov 6, 2013
- 150
- 0
OK thanks I just got this selling one of my modded consoles http://www.ebay.com/itm/X-TRONIC-40...-IRON-STATION-COMPLETE-KIT/111037604057?rt=nc does this look ok for this nice clean non cheap small tips
- Nov 6, 2013
- 150
- 0
ile be willing to trade but its just the chip no qsb or wires I do have a extra post out ribbon cable to bundle it with If you have some ile trayed for rev c rev b or proto chip by itself because I have allot of wire almost the same as the wires it comes with?