cannot dump xenon nand

[jhaymes2006]

I cannot dump nand on xenon, with dash 2.0.12625.0. I have soldered the qsbs onto the motherboard, and sent the command in nand pro, and it says command not recognizable so i was wondering if you guys would look at the pics and make sure i have everything set up right to extract nand. Power cord is in the drivers are installed its being recognized in device manager. command i sent is nandpro usb: -r16 john.bin. any ideas, is this the correct setup for a xenon?

 

[BL4K3Y]

You cannon JTag your console because your dashboard is newer than 7371 and the eFuses have been blown. I'm sorry to be the bearer of bad news mate but that's just the way it is.

 

[jhaymes2006]

in the guide it says, i can jtag as long as the dash is under 2.0.8955.0 http://team-xecuter.com/forums/showthread.php?t=53537. also the system still works i havent tried to jtag it yet i only tried to read the nand. i could be wrong on this though.

 

[BL4K3Y]

Your dashboard is 12625 which is higher than 8955. I suggest de-soldering everything and leaving the console as it is.

 

[jhaymes2006]

ok thank you i totally see what your saying i feel like a dumb @@@ now. i will desolder and stop once again thanks for showing me.

 

[BL4K3Y]

ok thank you i totally see what your saying i feel like a dumb @@@ now. i will desolder and stop once again thanks for showing me.

Don't put yourself down, we all have to start somewhere and learn from our mistakes .

 

[jhaymes2006]

That is why im always using team x though my question was answered in like 2 minutes.

 

[frazzeld]

I thought you wanted to dump the nand? you can still dump the nand at 12625 in readiness of the reset glitch

 

[BL4K3Y]

I thought you wanted to dump the nand? you can still dump the nand at 12625 in readiness of the reset glitch

The reset glitch does not (and probably never will) work on Xenon consoles .

 

[frazzeld]

if thats the case.....he can still dump the nand though! it comes in useful for practice or even AP25 protection

 

[jhaymes2006]

will it not dump the nand because the xenon update is not out. will a xenon not dump the nand unless its j-tagable. if i had that same setup on a jasper for a reset glitch would i have gotten my nand?

 

[BL4K3Y]

You can dump the NAND but you can't do anything with it because you won't be able to retrieve the CPU key. You would have been able to run the reset glitch if you had a Jasper.

 

[jhaymes2006]

i have a jasper but i am waiting for the coolrunner, no big deal since no launcher out yet anyway.

 

[BL4K3Y]

i have a jasper but i am waiting for the coolrunner, no big deal since no launcher out yet anyway.

To be honest, i'd just keep your Xenon for XBOX Live or something and use the Reset Glitch on the Jasper .

 

[jhaymes2006]

so is that al that i needed to have hooled up from my understanding of the tutorial all i needed was the wires from the nand x the 7 wires is that correct?

 

[BL4K3Y]

Yes, there's just 7 wires to install in order to read/write the NAND.

 

[jhaymes2006]

ok thanks again!

 

[jhaymes2006]

i just tried a jasper to dump the nand out of curiosity, and when i tried i had the wires soldered to the board, and the plug in in the 360 but not on. i sent the command nandpro usb : -r16 nand 1.bin, it says something along command not recognized, the same thing as the xenon, not trying to jtag or reset glitch just wanted to see if i could get my nand. you can check out my soldering from the pics above on the xenon. im runnin nandpro v2.0 e the nand-x is recognized as

pruftecnik usb devices
xecuter usb nand-x usb

any ideas as to what might be wrong i have a magnifying light and have checked for shorts and cant find any. sounds like a problem with nand-x recognizing my pc, but i dont know.

 

[BL4K3Y]

That command should work find in NandPro. Have you changed to the NandPro directory in CMD?

 

[jhaymes2006]

I go to run type in cme hit enter, then I open nandpro v2.0e folder drag the .exe file to cmd it pops up a few paragraphs and commands and then I paste that command and hit enter and it says command not recognized.