RGH Cant boot in Xell with Slim Proto

[Rexylian]

Hi there,

I need some help again. :-(
I have a corona v3 and i did a quick install today, but i cant get Xell to boot.
Dashboard version is: D:2.0.16197.0 - K:2.0.16197.0 (BK:2.0.1888.0)

Hardware:
- Xecuter Coolrunner Corona Upgrade QSB v3
- Xecuter Postfix Adapter
- Xecuter Slim Proto

I can read/write the nand without any errors
i created the ecc file and wrote it to the nand and tried to boot it.

When i hit the powerbutton or the eject the fan does start and the centre light turns green.
The led1 on the Slim Proto is always red.

The xbox is not showing up in the router either.
What can i do?
I attached some pictures. I can make more if you want.

 

[BL4K3Y]

Does LED2 blink every few seconds?

Set dip switches 3 and 8 ON and tell us what happens.

 

[Slayertex6]

You mentioned creating xell, just use the premade xell in j-runner. Ecc is what I meant to say.

 

[Rexylian]

Update:

I checked al my soldering and forget to solder one pad on the botton qsb... (Thx Youtube)
How the led2 on the Slim Pro starts to blink green every two seconds or so.
I've put DIP 3 and 8 on...
I didn't trim the wires yet.

Still no xell :-(

Is the Slim pro glitching? Do i have to trim down the wiring?
To test I wrote back the orgininal Nand and it boots up just fine.

Steps in J-runner:
Read Nand, CReate ECC, Write ECC

 

[Dosk3n]

Yes if the green light is blinking that would usually means its attempting to glitch.

 

[BL4K3Y]

Update:

I checked al my soldering and forget to solder one pad on the botton qsb... (Thx Youtube)
How the led2 on the Slim Pro starts to blink green every two seconds or so.
I've put DIP 3 and 8 on...
I didn't trim the wires yet.

Still no xell :-(

Is the Slim pro glitching? Do i have to trim down the wiring?
To test I wrote back the orgininal Nand and it boots up just fine.

Steps in J-runner:
Read Nand, CReate ECC, Write ECC

Did you bridge the R2C6 and R2C7 pads?

I can't see if they are bridged in your image.

Did you try dip switch 3 ON (dip switch 8 needs to be left on at all times on Corona boards)?

 

[Rexylian]

Yes,

i bridged R2C4, R2C6 and R2C7
DIP 3 and 8 are set to ON.
Is my wiring correct? ( So i can close the old thead...)

 

[Rexylian]

I have a fully updated J Runner program.
Does it come with the new Xell with Corona support? or do i have try the latest Xell?

 

[XMonsterModsX]

the new updated j runner comes with the new xell for coronas , is your cpu_rst wire cut to 12 cm?

 

[Rexylian]

No i havent done anything with the wirelengh or routing. I will try it tomorrow. How do i know if the postfix adapter pin is touching the cpu?

 

[Rexylian]

YES!!! It boots Xell!!! Thank you !
Couldn't get to sleep so i cut down the cpu wire to 12 cm and rerouted it.
It boots xell in 1 glitch evertime!

Tomorrow i will take some photos and make a nice tut for you all

Thanks all for helping this noob

 

[Antalpromille]

YES!!! It boots Xell!!! Thank you !
Couldn't get to sleep so i cut down the cpu wire to 12 cm and rerouted it.
It boots xell in 1 glitch evertime!

Tomorrow i will take some photos and make a nice tut for you all

Thanks all for helping this noob

There is already a tutorial/install instruction with some good setup examples, there is also a complete thread with successfull setups that you could have looked at and found out that you should have cut your cpu_rst wire to increase your chances.

 

[jdoe91011]

Not for nothing, but the CPU_RST wire that comes with the Proto V2 kit is super long if you don't cut it!! no wonder it wasn't glitching

 

[chronic1553]

this thread is over 4 months old