cant install dashlaunch

P

pytkin

Full Member
Jan 11, 2017
29
0
Hi, i cant install dashlaunch on trinity xbox with rgh, i get error: dashlaunch cannot be installed kernel not supported. Dashboard is 17511 version. I try to install 3.18.1 dashlaunch version, which working very well on another xboxes with 17511 kernel. Its a problem with rgh on this xbox ? When i try to start aurora, i get only black screen, and xbox not working. But xexmenu and freestyledash working fine.

Main problem is with booting xbox into fsd. When i cant install dashlaunch, then i cant set a patch in dashlaunch for booting software in and i cant save it. So, is here any other solution, how to boot into FSD directly after starting xbox ? Thanks.

edit.1: I downloaded launch.ini file, set default patch for FSD, copied .ini on fat32 usb and copied .ini on internal hdd1 in xbox. But its not working, xbox always booting to NXE.

edit.2: I tried reflash the nand, but i got same error again .. dashlaunch cannot be installed ..

edit.3: I tried to delete launch.ini in Flash Memory through Xexmenu, but it look like i havent permission or something, because i cant delete it and also i cant rewrite it with my launch.ini file from usb ..

edit.4: ok i can CUT launch.ini file from Flash. But launch.ini from HDD1 still not booting to FSD. I have set in launch.ini : Default = hdd:\FreeStyle\default.xex and i tried also: Default = hdd1:\FreeStyle\default.xex .. i tried to boot from usb too, but still nothing ...

On hdd1 i have a FreeStyle folder and inside is default.xex .. Where can be the problem ? thanks
(sorry for english)




 
Last edited:
G

gavin_darkglide

VIP Member
Dec 14, 2012
2,303
118
Make sure you are building your nand image with the correct version of dashlaunch pre installed in it. I have never had a problem with the installer, but this should fix the problem.
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
gavin_darkglide said:
Make sure you are building your nand image with the correct version of dashlaunch pre installed in it. I have never had a problem with the installer, but this should fix the problem.
Click to expand...
just what i was gonna say.
 
Joo C

Joo C

VIP Member
Dec 2, 2011
748
48
South Africa
It's odd! If you have access to another rgh console try popping the hard drive into the working console and configure dashlaunch then transfer the hdd
 
P

pytkin

Full Member
Jan 11, 2017
29
0
So i have to try updating system ? or what ? I probably didnt understand it well
 
Joo C

Joo C

VIP Member
Dec 2, 2011
748
48
South Africa
pytkin said:
So i have to try updating system ? or what ? I probably didnt understand it well
Click to expand...
after writing the freeboot nand it is necessary to run a system update unless the console was already on an equal or higher dash than the dash you have created. So for instance if your console was on 16537 before the RGH and you built a 17511 image you need to update it with an official 17511 systemupdate or '$$ystemUpdate'. Outside of this I dont know if I will be of any further help-good luck
 
BL4K3Y

BL4K3Y

VIP Member
Jul 7, 2010
13,721
118
Colne, Lancashire (UK)
If the console is using the internal HDD to boot from, the default line should read:

Code: 
Default = Hdd:\FSD\Default.xex

This assumes your folder is named "FSD" - edit accordingly if it is named something different.

To ensure DashLaunch is installed, you can either run the installer or build a new image with "DashLaunch Patches" checked in J-Runner before building the image.
 
Last edited:
  • Like
Reactions: Joo C
You must log in or register to reply here.