cant read nand for sh*t what that hell happen?

[arpsachin2]

I have modded more than 25 consoles now.

I got that error a LOT during my first few xbox's.

It's NOT the xbox and it's NOT the Nand-x. It's the soldering.

99.9% it's the soldering.

 

[juanbrnt]

I have modded more than 25 consoles now.

I got that error a LOT during my first few xbox's.

It's NOT the xbox and it's NOT the Nand-x. It's the soldering.

99.9% it's the soldering.

i dont know if this happen to any body but let said the console is about to get rrod if is a possibility the nandx stop working into you correct the problem with the console?

 

[arpsachin2]

i dont know if this happen to any body but let said the console is about to get rrod if is a possibility the nandx stop working into you correct the problem with the console?

I am tellin you from my experience.

My jasper has RROD. It still reads/write nand.

 

[Evil0ne]

last nitgh i rgh 4 consoles using nand x, this morning i try to do 2 more i cant read nand it keep saying in j runner cant continue what the hell my soldering ,belive me is good so i dont know whats going on i try other cables and nothing please anyone knows what going on or whats the problem?:mad2:

have u Tried plugging the nandx in question back into a "known" good working box like your personal box that u know works 100%, to test if its xbox/nandx it could also be blown spi's but i doubt it if both boxes are brand new, and the fact they happened on 2 boxes makes it not likely

 

[Martin C]

i dont know if this happen to any body but let said the console is about to get rrod if is a possibility the nandx stop working into you correct the problem with the console?

How about this - with the CPU and GPU REMOVED from the board, you should be able to STILL dump the NAND provided the southbridge circuitry is intact. Yes, this is possible as I've done it.

 

[Evil0ne]

How about this - with the CPU and GPU REMOVED from the board, you should be able to STILL dump the NAND provided the southbridge circuitry is intact. Yes, this is possible as I've done it.

As have i, seeing how the nands paths dont use the cpu/gpu at all it shouldnt b a problem, so as i said in my previous post id check it on a known workin board to tell if its the nandx/xbox

 

[Loomingx]

Had the same issue with mine. Replaced it with the same wiring still attached to the board, received the new NandX and all worked.

I've had my new NandX for about a month and guess what...same issue again.

I've never had trouble with any other TX products but there is clearly an issue that is making all of these NandX's not work.

 

[Statecowboy]

Hopefully you have not flashed your coolrunner while the console is powered up. This will bork your nand-x. (I speak from experience)

Or booted the console with the coolrunner in normal mode and still connected to your nand-x.

 

[Loomingx]

I may have done it with my first Nandx but after getting my second I took every step necessary to make the same mistake. I Jtagged two consoles (1 slim, 1 Jasper) and since then I haven't been able to get a Nand read. I bought this Nandx from Xconsoles about a month ago. I know it's under warranty it's just a pain to return it, wait for a new one, not to mention shipping which is almost a 3rd of the cost of the Nandx to begin with.

I'm the last person to trash TX products. They have been easy to use and very lucrative for me but this seems like a real issue that needs addressing.

 

[Ubergeek]

Every one we get back with this error has had the same cause every time.

Its always down to programming the CoolRunner while it's installed to the Xbox and the switch not being set to prg before the cable is connected.

I don't know what else to tell you.

Where are you? I will be happy to a replace it for you this one time and will cover the shipping.

 

[Ubergeek]

Hopefully you have not flashed your coolrunner while the console is powered up. This will bork your nand-x. (I speak from experience)

Or booted the console with the coolrunner in normal mode and still connected to your nand-x.

Exactly

 

[Loomingx]

Every one we get back with this error has had the same cause every time.

Its always down to programming the CoolRunner while it's installed to the Xbox and the switch not being set to prg before the cable is connected.

I don't know what else to tell you.

Where are you? I will be happy to a replace it for you this one time and will cover the shipping.

This I understand. It's how I "borked" my first one. Once I received my 2nd one I was careful not to make the same mistake which Is why I was surprised to find my NandX not working today after a month and having RGHed two consoles with no issues.

I'm in Toronto. (Not sure if you're offer was to me or the thread starter)

 

[juanbrnt]

ok guys i just got back my 2 nand x from x console and i used them working fine with the same soldering the i did when i got it messup .ubergeek yes all this time i been having the cool runner ready set up in the xbox when i try to rgh them,i star doing this when j runner tool came up , probably in few occasion i did forgot to set it back to prg or nor thanks again for the support,is one thing about tx product warranty is great

 

[skater411]

im having same issue so i'm thinking i did the same thing

 

[juanbrnt]

im having same issue so i'm thinking i did the same thing

did 4 consoles today and it work fine i guess thats the way to do it do everythng else and then install the cool runnner when you are about to get the cpu key

 

[wills123]

just flash the coolrunner first before anything else, presuming you can work out the board revision, and if you cant google it lol,

 

[avenged06x]

I am actually having the same problem with one of my nand-x's. But I know the power cable wasn't connected while I flashed the Coolrunner.

How do I get the replacement? Contact Xconsoles?

 

[myst77]

hello
i just got a NAND-X v3

i soldered the QSB on my slim and i can not read NAND

The error in Jrunner is:

Flash Config: 0x00000000
Can not Continue
Can not continue

The soldering is OK, i tested it with a multimeter
i tried it both in WinXP and Win7
The console is plugged but turned off
I tried to reflash the NAND-X v3

What can i do please?

 

[Martin C]

hello
i just got a NAND-X v3

i soldered the QSB on my slim and i can not read NAND

The error in Jrunner is:

Flash Config: 0x00000000
Can not Continue
Can not continue

The soldering is OK, i tested it with a multimeter
i tried it both in WinXP and Win7
The console is plugged but turned off
I tried to reflash the NAND-X v3

What can i do please?

You also can't read the rules. No thread-jacking. Start a new topic and read up on my NAND-x guide.


Sent from my iPad using Tapatalk HD