RGH Cant read XBOX 360 E NAND

H

hamodwii

Senior Member
Apr 22, 2010
123
0
BAHRAIN
TX Product(s) used: J-R Programmer
Console Type: CORONA V5
NAND size: 16MB
Dashboard version: 2.0.16203
CB version: DONT KNOW YET
Screenshot of NAND details from J-Runner:
still
J-Runner log:
Version: 01
Flash Config: 0xFFFFFFFF
IoTimedOut

IoTimedOut:No more bytes!
FFFFFFFF
updflash.bin log (if applicable):
Image of Coolrunner:did int get there yet!
Images of close-up soldering to motherboard:
IMG_6591.jpg
IMG_6592.jpg
IMG_6593.jpg

Description of problem:
Hi all
i am trying to read this 360e corona v5 nand but it always gives me this massage:
Version: 01
Flash Config: 0xFFFFFFFF
IoTimedOut

IoTimedOut:No more bytes!
FFFFFFFF
i am using j-programer and my soldering is fine as u can see
bridged the following points:
R2C4
R2C6
R2C7
R2C10 THE RESISTER IS ALREADY THERE.

tried updating the j-programer also didnt work.

any help!
Was the console working before you started: Y
 
H

hamodwii

Senior Member
Apr 22, 2010
123
0
BAHRAIN
BL4K3Y said:
Can you confirm that the thicker red wire is soldered to the GND pin on the JRP?
Click to expand...
yes i checked it again and i tested on old corona and it worked nice!
maybe its the point that i connected the grn in the mother board?
i will try the grn point in the motherboard
 
A

axelll

VIP Member
Mar 1, 2011
469
17
Everywhere
Are you sure this isn't a 4Gb board?
 
H

hamodwii

Senior Member
Apr 22, 2010
123
0
BAHRAIN
Ben c said:
Isnt the v5 hex the latest up to date file for CR?
Click to expand...
in commen folder i only have this files:


ArmV3.hex (no green light after write hex)
PICFLASH_E_1_0_4_ISD_BIT.HEX ( after writing it to the j-programmer the programmer will give green light and it will give the Flash Config: 0xFFFFFFFF)
PICFLASH_E_1_0_4_JRP1_ISD.HEX( after writing it to the j-programmer the programmer will give green light and it will give the Flash Config: 0x00000000)
PICFLASH_E_1_0_5-JRP-V2.HEX (no green light after write hex)
 
Last edited:
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
You don't have the upgrade board for your J-R Programmer, so you should be using PICFLASH_E_1_0_4_JRP1_ISD.HEX.

You still need to post your voltage/resistance values as per the NAND-x troubleshooting guide.
 
H

hamodwii

Senior Member
Apr 22, 2010
123
0
BAHRAIN
Martin C said:
You don't have the upgrade board for your J-R Programmer, so you should be using PICFLASH_E_1_0_4_JRP1_ISD.HEX.

You still need to post your voltage/resistance values as per the NAND-x troubleshooting guide.
Click to expand...
ok here are the readings:
1- 1v
2-3.19v
3-2.36
4-0v
5-307 v
6-0v

i tried to connect pin 2 direct to the resisster and it tyrned from 0xFFFFFFFF to 0x00000000

thanks.
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Infraction issued for unnecessary bumping.

The problem here is you can't solder. You've already messed up points on the J-R Programmer. Bumping your help request won't get it resolved any faster. I suggest letting someone RGH it for you.
 
H

hamodwii

Senior Member
Apr 22, 2010
123
0
BAHRAIN
OK I WILL TRY TO USE THE DEMON ON THIS ONE AS ITS AS SAME AS THE CORONA V3 , BUT I JUST CANT FIND A TUTORIAL ON HOW TO READ AND WRITE THE NAND USING THE DEMON WITH J-RUNNER, I WILL JUST READ THE NAND AND WRITE ECC AND THE HACKED NAND AND REMOVE THE DEMON AFTER.
CAN SOME ONE SHOW ME HOW TO READ THE NAND WITH DEMON USING J-RUNNER
THANKS
 
You must log in or register to reply here.