RGH Causes for E71 on DemoN

[Shadowlance]

What could cause E71 on a demon? Ive tried the advice of this thread ---> http://www.team-xecuter.com/forums/showthread.php?t=91220

Still the same, retail give e71 on the demon but everything works fine on the console nand. I've reseated the coolrunner cable a couple times, erased and re wrote the demon, xell boots fine on it. I'm at a loss. Ill post some pics once i get them of my phone. Everything i've read points to a software issue, i updated to 14719 and got some fresh nand dumps to try and still the same. If i have the dvd drive and hdd plugged in it freezes after the splash screen instead of throwing and e71.
This is on a trinity also. and yes pics will be coming in the morning.
Thanks for any info!

 

[Martin C]

Build your RGH image with the option 'noremap' then use the Write Fusion option to write it to the DemoN.

 

[Shadowlance]

I'll give that a shot later today, also could the routing of the demon wires cause e71 or is it mainly a NAND error?

 

[Martin C]

E71 is failure to load the dashboard in general, often caused by bad blocks.

Read the NAND using the DemoN toolbox and paste the output.

 

[junivelli]

Did you tried to remap the bad blocks ?
you can also try another software to build your nand

 

[Shadowlance]

So i've tried noremap and wrote it as normal and again as fusion, still no luck. Could it be an issue with the actual nand on the demon? Ill try and get ahold of a copy of multi and give that a shot.

Here's the log if that helps any:

===================================================
Tuesday, November 13, 2012 5:42:26 PM

J-Runner v0.2 Beta (283) Started



Checking Files
Finished Checking Files
Initializing Nand..
Nand Initialization Finished
Initializing Nand..
CpuKey is Correct
Key already Exists
Nand Initialization Finished
Load Files Initiliazation Finished
14719
Started Creation of the 14719 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.05.548
---------------------------------------------------------------
building glitch image
---------------------------------------------------------------
C:\Users\Chaotic\Desktop\J-Runner\153139611005\updflash.bin image built, info:
---------------------------------------------------------------
Console : Trinity
NAND size : 16MiB
Build : Glitch
Xell : power on console with console eject button
Serial : 153139611005
ConsoleId : 006448722104
MoboSerial: 7827513113161105
Mfg Date : 02/27/2011
CPU Key : 668188E78F612BB86AA563DAE636B253
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : D1F7A3F2426831BB9243291B9C294CA8
CF LDV : 6
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------

Saved to C:\Users\Chaotic\Desktop\J-Runner\153139611005
Image is Ready
DemoN
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks :
Writing Nand
Starting remapping process
Done!
in 0:32 min:sec

Success
Success
Options.ini file was altered successfully
Using edited settings
Load Files Initiliazation Finished
14719
Started Creation of the 14719 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.05.548
---------------------------------------------------------------
building glitch image
---------------------------------------------------------------
C:\Users\Chaotic\Desktop\J-Runner\153139611005\updflash.bin image built, info:
---------------------------------------------------------------
Console : Trinity
NAND size : 16MiB
Build : Glitch
Xell : power on console with IR power button
Serial : 153139611005
ConsoleId : 006448722104
MoboSerial: 7827513113161105
Mfg Date : 02/27/2011
CPU Key : 668188E78F612BB86AA563DAE636B253
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : D1F7A3F2426831BB9243291B9C294CA8
CF LDV : 6
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------

Saved to C:\Users\Chaotic\Desktop\J-Runner\153139611005
Image is Ready
DEMON
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Writing Nand
Done!
in 0:32 min:sec

Success
Success
Options.ini file was altered successfully
Using edited settings
Load Files Initiliazation Finished
14719
Started Creation of the 14719 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.05.548
---------------------------------------------------------------
building glitch image
---------------------------------------------------------------
C:\Users\Chaotic\Desktop\J-Runner\153139611005\updflash.bin image built, info:
---------------------------------------------------------------
Console : Trinity
NAND size : 16MiB
Build : Glitch
Xell : power on console with IR power button
Serial : 153139611005
ConsoleId : 006448722104
MoboSerial: 7827513113161105
Mfg Date : 02/27/2011
CPU Key : 668188E78F612BB86AA563DAE636B253
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : D1F7A3F2426831BB9243291B9C294CA8
CF LDV : 6
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------

Saved to C:\Users\Chaotic\Desktop\J-Runner\153139611005
Image is Ready
DemoN
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks :
Writing Nand
Starting remapping process
Done!
in 0:32 min:sec

Current: DemoN
Switching to XBOX
Success
Current: XBOX
Switching to DemoN
Success
Success
Success

 

[Shadowlance]

just noticed something, to the right of the ldv info it says 0xB4DEAD could that be what's wrong?

tried with multi and it freezes instead of rdod

 

[Duhasst0]

Have you tried to read out the nand that is on the demon itself? It may have somw bad blocks that arr not being remapped at all. Once you do that then post your results.

 

[junivelli]

try to make another hacked nand with AutoGG 0.8.1 from your original one, and dont remapped anything, put it back on the Demon,

 

[Martin C]

I asked for a screenshot from DemoN Toolbox.....?

 

[Shadowlance]

***** NAND-Flash Information *****

Manufacturer: Hynix
Device: HY27US08281A
Device Id: 0xAD73
Number of Blocks: 1024
Number of Pages per Block: 32
Page Size: 528 bytes
Number of Invalid Blocks: 0

Full backup selected.
Reading.
ERROR: Block 248, page 0 contains corrupt data.

 

[Martin C]

ERROR: Block 248, page 0 contains corrupt data

So it's possibly this which is the problem.

Erase the NAND on the DemoN and read it again.

 

[Shadowlance]

erased and read with demon toolkit

***** NAND-Flash Information *****

Manufacturer: Hynix
Device: HY27US08281A
Device Id: 0xAD73
Number of Blocks: 1024
Number of Pages per Block: 32
Page Size: 528 bytes
Number of Invalid Blocks: 0

Full backup selected.
Reading.
Reading completed successfully in 28 seconds!

 

[Martin C]

Now use DemoN Toolbox to write your image made in J-Runner with noremap and post the result.

 

[omoikorodu]

I have the same problem last weekend installing Demon. The regular nand will boot but the Demon will give either E71 error or no power when pressing the power button. Disconnecting and reconnecting the power source the demon with boot normally sometime. My problem was the
ground wire on the Demon. I re-solder the ground wire and the problem was solve. Thanks, Martin C for that. I took your advice on someone post.

 

[Shadowlance]

***** NAND-Flash Information *****

Manufacturer: Hynix
Device: HY27US08281A
Device Id: 0xAD73
Number of Blocks: 1024
Number of Pages per Block: 32
Page Size: 528 bytes
Number of Invalid Blocks: 0

Loading image.
Remapping invalid blocks.
Erasing.
Marking invalid blocks.
Programming.
Programming completed successfully in 30 seconds!

And E71, was a fresh image created from 2 dumps after updating to 14719, i updated yesterday to get a good clean nand, nand dumps show no bad blocks in j runner.
--Is there any chance it could be the nand on there is hooped? I have a dead trinity i could pull the nand off and put on there, alot of work for a trial and error though lol

 

[Martin C]

Just a thought.

E71 can be southbridge, as mentioned.

Can you post images of your soldering?

 

[Shadowlance]

I can post some iphone 4 pics but that's my capability right now, let me see if i can get some good pics up for you here in a minute. Also thank you guys for all the help, i lurk quite a bit and learn what i can but it's a never ending learning curve with this lol

 

[Shadowlance]

Just a thought.

E71 can be southbridge, as mentioned.

Can you post images of your soldering?

If it was the southbridge, wouldnt it affect both the demon and the console nand?

 

[Martin C]

If it was the southbridge, wouldnt it affect both the demon and the console nand?

It's not that - there's a SBR wire which is soldered and wanted to make sure it was ok.

Do me a favour - write your working stock NAND to the console and read it back as something else. Don't turn on the console in between write/read then compare the dumps.