check my nand pls

b3datarin

b3datarin

VIP Member
May 30, 2011
194
23
Iran
hi guys
one of my consoles have this backup .
i don't know old history of this one but console is oldest series of jasper.
when i load it with AutoGG . say nand have Xell or corrupted .
console have cd 8453 and i think this CD could not be JTAG .
so console don't boot with or without jtag instal .

can i remove xell from this nanddump .
i have no cpukey .

what can i doing ??
i did not have any JTAG console before .

no cpukey & original dump i have . :(
 
b3datarin

b3datarin

VIP Member
May 30, 2011
194
23
Iran
yes but CD is 8453 .

jtag wire and diods installed .

but console wont boot after about 1 min 3 green light and then 2 redlight.num 2 and 3 LED. !!!!
when i load nanddump with XnandHealer Jtagable is YES .
in ECC section i have " zeropair (v.1) "
what is mean
 

Attachments

Last edited:
R

rishank

Full Member
Feb 4, 2014
51
0
try j-runner programmer and and j-runner software then report with your installation picss
 
PetrozPL

PetrozPL

Junior Member
Jun 6, 2013
24
0
The best bet would be installing RGH and obtain cpu_key from xell. Install as for RGH2 and write pre-created ECC. Grab the cpu-key, fuseset and extract your KV (decrypted) from this nanddump. Then, according to cseq value in nand generate clean image. Voila. From this point you're good to go with any other mod you like (jtag/rgh/rgh2), according to your console fuses of course.
 
b3datarin

b3datarin

VIP Member
May 30, 2011
194
23
Iran
PetrozPL said:
The best bet would be installing RGH and obtain cpu_key from xell. Install as for RGH2 and write pre-created ECC. Grab the cpu-key, fuseset and extract your KV (decrypted) from this nanddump. Then, according to cseq value in nand generate clean image. Voila. From this point you're good to go with any other mod you like (jtag/rgh/rgh2), according to your console fuses of course.
Click to expand...
thanks alot .
JRunner could not create ECC for this nand when RGH & RGH2 is selected .
only JTAG and only Xell-Reloaded .
how can i make ECC ?

you sure RGH2.0 wiring Needed ?
 
b3datarin

b3datarin

VIP Member
May 30, 2011
194
23
Iran
RGH1.0 wire installed.
ECC wrote . ( used nandpro and +w16 for write ECC )
and Green light on CR wont blink .
RGH2.0 wiring needed ? ???
 
Last edited:
BrockThunderjam

BrockThunderjam

VIP Member
Jun 25, 2013
1,503
88
His CB is 6723.....
 
A

AllyNerd

VIP Member
Feb 25, 2013
1,179
0
Philadelphia
Since this is turning into a help thread you should fill out the rgh template with pics. Also y don't you use j runner?
 
Last edited:
BrockThunderjam

BrockThunderjam

VIP Member
Jun 25, 2013
1,503
88
jsinger47 said:
And your point is?

It is quite likely someone has written a JTAGable Xell to this console when the console isn't JTAG exploitable.
Click to expand...
My point is he is confusing CD and CB, scroll up and read. I understand what's going on, I'm trying to make sure the OP does as well.
 
b3datarin

b3datarin

VIP Member
May 30, 2011
194
23
Iran
console have xellreload on nand and i don't have original backup .
CB say Jtagable and CD say NO .
also console in RGH 1.0 mod won't glitch .( coolrunner won't blink green LED)
what can i do ?
somebody tell me Masters .
 
jsinger47

jsinger47

Troll Eating Dogs
Feb 6, 2011
8,133
128
Grand Rapids, MI
BrockThunderjam said:
My point is he is confusing CD and CB, scroll up and read. I understand what's going on, I'm trying to make sure the OP does as well.
Click to expand...
I'm not seeing any confusion at all. Not sure what you're getting at.

b3datarin said:
console have xellreload on nand and i don't have original backup .
CB say Jtagable and CD say NO .
also console in RGH 1.0 mod won't glitch .( coolrunner won't blink green LED)
what can i do ?
somebody tell me Masters .
Click to expand...
Install RGH2 and write the RGH2 generic .ecc.

If you have an RJTAG or CR3 pro, i would monitor fullpost so we can see where the console is going wrong in the boot process.
 
b3datarin

b3datarin

VIP Member
May 30, 2011
194
23
Iran
jsinger47 said:
I'm not seeing any confusion at all. Not sure what you're getting at.



Install RGH2 and write the RGH2 generic .ecc.

If you have an RJTAG or CR3 pro, i would monitor fullpost so we can see where the console is going wrong in the boot process.
Click to expand...

thanks .
RGH2.0 installed . i used ecc file from common folder on jrunner and JASPER.ECC
Green led blink normal . but console won't boot .
all timing file and wiring tested .
can you give me RGH2.0 ECC file . do you have ?
 
jsinger47

jsinger47

Troll Eating Dogs
Feb 6, 2011
8,133
128
Grand Rapids, MI
b3datarin said:
thanks .
RGH2.0 installed . i used ecc file from common folder on jrunner and JASPER.ECC
Green led blink normal . but console won't boot .
all timing file and wiring tested .
can you give me RGH2.0 ECC file . do you have ?
Click to expand...
You have installed it as i said. The Jasper.ecc is what i was talking about.

I would recommend installing fullpost to see where the problems in booting are coming from.
 
You must log in or register to reply here.