RGH Cmd error

Status
Not open for further replies.
S

sendyo

Senior Member
Mar 4, 2012
110
0
I am using this guide http://team-xecuter.com/forums/showthread.php?t=76193

I get this error in CMD First part


C:\Users\Sendyo\Desktop\nandpro3>
C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r16 nanddump.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r16 nanddump2.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>
C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r64 nanddump.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r64 nanddump2.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>
 
A

AMIT

VIP Member
Nov 30, 2011
943
68
INDIA
use j-runner !
BTW- it's can't find any USB SPI nand flasher !
which nand flasher are you using ?
if nand-x which version & is nand-x drivers installed ?
 
Last edited:
D

daftdog198

Senior Member
Oct 8, 2011
140
0
doncaster
Hi.
This is most likely your soldering.
You are getting this error as nandpro cant find the nand.
Do you have the power supply plugged into the xbox, it needs to be plugged in but not turned on.
Have you installed the drivers for the nand-x
 
S

sendyo

Senior Member
Mar 4, 2012
110
0
The power is plugged in, Drivers are installed.

I'm using NAND-X V3.
 
Last edited:
D

daftdog198

Senior Member
Oct 8, 2011
140
0
doncaster
Hi.
Yes definatly a soldering issue if your sure everthing else is ok.
Make sure the wires are correctly positioned and that none of the points are bridged.
Check to see if the console still boots. You can leave the wiring in place but disconnect the nand-x before you turn on the console
 
sherlock

sherlock

Troll Eating Dogs
May 24, 2009
1,926
78
Baker street, Stoke-on-Trent, England
sendyo said:
I am using this guide http://team-xecuter.com/forums/showthread.php?t=76193

I get this error in CMD First part


C:\Users\Sendyo\Desktop\nandpro3>
C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r16 nanddump.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r16 nanddump2.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>
C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r64 nanddump.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>nandpro usb: -r64 nanddump2.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Can not continue

C:\Users\Sendyo\Desktop\nandpro3>
Click to expand...

only one thread per question, i've deleted the one from here http://team-xecuter.com/forums/showthread.php?t=84863

as you are receiving help in this one.
 
  • Like
Reactions: sendyo
A

AMIT

VIP Member
Nov 30, 2011
943
68
INDIA
post your NAND-X wires or qsb installation pics !
 
Last edited:
D

daftdog198

Senior Member
Oct 8, 2011
140
0
doncaster
Hi.
The blue wire looks like it is bridged to the point next to it.
The orange wire is definately bridged to the point next to it and the red wire looks like it is soldered to the wrong point but the point where it it supposed to be soldered to looks burnt so you may need to use a alt point for power.
To help with reading your nand we need to see your nand-x install
 
S

sendyo

Senior Member
Mar 4, 2012
110
0
Okay.

---------- Post added at 18:35 ---------- Previous post was at 18:34 ----------

I didn't do the NAND-X install, Using the Pin header method but not sure how to connect to CoolRunner.
 
D

daftdog198

Senior Member
Oct 8, 2011
140
0
doncaster
Hi.
the nand-x pin headers go on the mainboard at points J1D2 & J2B1 but you dont need them you can just solder the nand-x wires straight to the mainboard
 
Status
Not open for further replies.