CORONA Confused about the installing

Toad86

Toad86

Full Member
Dec 11, 2014
42
0
Finland
  • Console Type: Corona v2
  • Programmer Used: JRP v2.0
  • NAND Size: 4GB
  • Dashboard version: 2.0.16767.0
  • CB Version: 13181
  • Was the console working before you started: Y
  • Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: N
Hello!

I have just attempted to mod Corona v2.
I got NAND read successfully by SD-card reader. And created ECC. And wrote ECC. Here's the log:

Code: 
Corona 4GB Manually Selected
H:\
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:18 min:sec
H:\
Initializing nanddump1.bin..
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump2.bin
Corona 4GB
RGH2 Selected
Nand Initialization Finished
Done!
in 0:19 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
H:\
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump3.bin
Done!
in 0:18 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
H:\
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump4.bin
Done!
in 0:18 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
ECC created
Connection TimeOut
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\image_00000000.ecc
Done!
in 0:02:207 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:21:423 min:sec:ms
Connection TimeOut
ECC created
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\image_00000000.ecc
Done!
in 0:00:774 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:21:423 min:sec:ms
Then i installed CR4.
The Xbox boots, but does'nt boot to Xell. The Xbox acts like it was never modded.
That's all i've done.


So can anyone tell what i need to do next? My ultimate goal is to mod this and install DemoN.

Do i need to program the CR4? And if so, what settings?
Is everything done as far that i can tweak the dip switches? And any guide for that?

THe Xbox 360 scene is very confusing when trying to find what goes where and so on.. :)
 

Attachments

J

JEFFreal

Full Member
Jan 9, 2006
92
0
Holland
Toad86 said:
  • Console Type: Corona v2
  • Programmer Used: JRP v2.0
  • NAND Size: 4GB
  • Dashboard version: 2.0.16767.0
  • CB Version: 13181
  • Was the console working before you started: Y
  • Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: N
Hello!

I have just attempted to mod Corona v2.
I got NAND read successfully by SD-card reader. And created ECC. And wrote ECC. Here's the log:

Code: 
Corona 4GB Manually Selected
H:\
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:18 min:sec
H:\
Initializing nanddump1.bin..
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump2.bin
Corona 4GB
RGH2 Selected
Nand Initialization Finished
Done!
in 0:19 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
H:\
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump3.bin
Done!
in 0:18 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
H:\
Reading from H:\ to C:\Users\Marko\Desktop\J-Runner\output\nanddump4.bin
Done!
in 0:18 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
ECC created
Connection TimeOut
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\image_00000000.ecc
Done!
in 0:02:207 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:21:423 min:sec:ms
Connection TimeOut
ECC created
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\image_00000000.ecc
Done!
in 0:00:774 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Writing to H:\ from C:\Users\Marko\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:21:423 min:sec:ms
Then i installed CR4.
The Xbox boots, but does'nt boot to Xell. The Xbox acts like it was never modded.
That's all i've done.


So can anyone tell what i need to do next? My ultimate goal is to mod this and install DemoN.

Do i need to program the CR4? And if so, what settings?
Is everything done as far that i can tweak the dip switches? And any guide for that?

THe Xbox 360 scene is very confusing when trying to find what goes where and so on.. :)
Click to expand...
if you dont get a green debug light something is not correct soldered. Check your wires...
 
X

xximod4uxx

Full Member
Jun 20, 2012
87
8
UK
Ok a few things...
You need to select CR4 box on the right of JR then create ecc and then write ecc DO NOT WRITE ORIGINAL NAND BACK, then power on your xbox with the dvd button and grab your cpu key.

Hope that helped
 
Toad86

Toad86

Full Member
Dec 11, 2014
42
0
Finland
xximod4uxx said:
Ok a few things...
You need to select CR4 box on the right of JR then create ecc and then write ecc DO NOT WRITE ORIGINAL NAND BACK, then power on your xbox with the dvd button and grab your cpu key.

Hope that helped
Click to expand...
Hmm... First i hit read NAND, box appears. Then i hit "read" when i see the correct "drive" on the list.
Then i hit "create ECC". Then i hit "write ECC".
Then the same box as previous, the "write" is available, and i hit that.
That's how i did it.
I don't know how else i'll do it?

Here's a screenshot of the J-Runner. So you can confirm i have right application. But as you can see, there is no "CR4 box" anywhere.
 

Attachments

X

xximod4uxx

Full Member
Jun 20, 2012
87
8
UK
Toad86 said:
Hmm... First i hit read NAND, box appears. Then i hit "read" when i see the correct "drive" on the list.
Then i hit "create ECC". Then i hit "write ECC".
Then the same box as previous, the "write" is available, and i hit that.
That's how i did it.
I don't know how else i'll do it?

Here's a screenshot of the J-Runner. So you can confirm i have right application. But as you can see, there is no "CR4 box" anywhere.
Click to expand...
Ok so i cant see what device you are using like jrp, nand x ect? but where it says xebuild choose the latest dash you can then select RGH 2 and the cr4 box will appear then press create ecc and write ecc
 
X

XDK

VIP Member
Sep 19, 2005
578
0
Houston, Texas
www.tortuga-cove.com
Toad86 said:
Hmm... First i hit read NAND, box appears. Then i hit "read" when i see the correct "drive" on the list.
Then i hit "create ECC". Then i hit "write ECC".
BOOT THE XBOX HERE TO GET CPUKEY
WHEN U HAVE KEY CREATE XEBUILD IMAGE
THEN FLASH UPDFLASH.BIN
Then the same box as previous, the "write" is available, and i hit that. (This restored stock retail nand)
That's how i did it.
I don't know how else i'll do it?

Here's a screenshot of the J-Runner. So you can confirm i have right application. But as you can see, there is no "CR4 box" anywhere.
Click to expand...
!see changes above in quote
 
Toad86

Toad86

Full Member
Dec 11, 2014
42
0
Finland
XDK said:
!see changes above in quote
Click to expand...
Ok, i see. And to clarify:
-The glitcher needs to be operational before i can get the CPU key?
-What devices do i need to get the CPU key? Do i need J-R-programmer, or is SD-card-reader all i need?
-And when i'm attempting to install DemoN, do i still need to flash the XeBuild image?

And what does this do?
Ok so i cant see what device you are using like jrp, nand x ect? but where it says xebuild choose the latest dash you can then select RGH 2 and the cr4 box will appear then press create ecc and write ecc
Click to expand...
 
Last edited:
nightmare0

nightmare0

BANNED
Jun 13, 2013
137
18
To get cpukey, you need to use glitch chip like cr4. Connected cr4, don't forget to tick cr4 option in jrunner. Don't create ecc, use cr4 ecc matching your mobo.
You don't need jrp, when you have 4gb console. Just 4gb nand rw kit.
If your board is corona v2 how did you dumped your nand with jrp? You need nand rw kit. What size does your dumps have?

You also cannot use DemoN in 4gb console.
 
Toad86

Toad86

Full Member
Dec 11, 2014
42
0
Finland
nightmare0 said:
To get cpukey, you need to use glitch chip like cr4. Connected cr4, don't forget to tick cr4 option in jrunner. Don't create ecc, use cr4 ecc matching your mobo.
You don't need jrp, when you have 4gb console. Just 4gb nand rw kit.
If your board is corona v2 how did you dumped your nand with jrp? You need nand rw kit. What size does your dumps have?

You also cannot use DemoN in 4gb console.
Click to expand...
I made the SD-adapter myself, and dumped the NAND with it(using J-Runner application). The dumps are 49152 kB

How do you mean by "use CR4 ECC matching your mobo"? Where to find that, and how to flash that?

And i'm going to do this for DemoN: http://www.teamx360.co.uk/showthread.php?2765-Here-s-how-To-Dual-Nand-The-Corona-V2
 
Toad86

Toad86

Full Member
Dec 11, 2014
42
0
Finland
Now i got Xell to boot. I got the CPU key, and made the XeBuild image, and flashed it in.

Xbox boots now like normal. Now i just need to figure out how to install custom firmware or something.
 

Attachments

You must log in or register to reply here.