Coolrunner 2 Nand-X Cable Issue

D

danielh2k11

Junior Member
Feb 10, 2012
15
0
Y

Younge

VIP Member
May 27, 2010
143
0
Why not use proper tools in nandpro it's ONE command Enter the following command into the command prompt window, and hit Enter. (Make sure to have Falcon.xsvf file in nanpro file and that the CMD is point in the nandpro folder) Easiest way is to click in the folder (not on a file) and hold shift and right click and hit "Open command window here" then just paste:

NandPro xsvf: Falcon.xsvf


Once the CoolRunner is programmed, it will say "Successfully executed file", in the command prompt window, and the Green LED will turn off.
 
D

danielh2k11

Junior Member
Feb 10, 2012
15
0
Younge said:
Why not use proper tools in nandpro it's ONE command Enter the following command into the command prompt window, and hit Enter. (Make sure to have Falcon.xsvf file in nanpro file and that the CMD is point in the nandpro folder) Easiest way is to click in the folder (not on a file) and hold shift and right click and hit "Open command window here" then just paste:

NandPro xsvf: Falcon.xsvf


Once the CoolRunner is programmed, it will say "Successfully executed file", in the command prompt window, and the Green LED will turn off.
Click to expand...
Thanks for that mate but ended in the same result :( Any other suggestions?
 
D

danielh2k11

Junior Member
Feb 10, 2012
15
0
tonyjandc said:
Call me an idiot but in the third picture it looks like the coolrunner is set to nor and not prg . If i am wrong then poke my eyes out with a blunt knitting needle
Click to expand...
You are correct, the switch is set to NOR. I thought this is where its suppose to be when it's not installed into the console. However I have tried switching it to PRG to find the same outcome.
 
D

danielh2k11

Junior Member
Feb 10, 2012
15
0
So what do you think the problem is? I personally think it could be a faulty wire? I have also tried programming the chip on a different pc with no difference.
 
Y

Younge

VIP Member
May 27, 2010
143
0
hmmmmmm try using another usb port, usb wire, things like that doesnt hurt

How sure are you that the nandx got updated?
 
D

danielh2k11

Junior Member
Feb 10, 2012
15
0
Younge said:
hmmmmmm try using another usb port, usb wire, things like that doesnt hurt

How sure are you that the nandx got updated?
Click to expand...
Still nothing, think im going to have to contact MrModchips now. What do you think I should say to them, Its a faulty wire or faulty board?
 
T

tonyjandc

VIP Member
Dec 30, 2011
481
0
london uk
Ok had a problem like yours found when pushing nand x wire into coolrunner the green wire was loose on adapter these can pull quite easy check all wires are secure I know it sounds silly but this can happen I repaired mine and now it lives in nand x all the time i put some tape around the wires to give better support
 
D

danielh2k11

Junior Member
Feb 10, 2012
15
0
Younge said:
i just noticed that it looks pulled out make sure it's making contact
Click to expand...
Do you mean the yellow wire? http://i.imgur.com/daXiZ.jpg It looks out alot but wont go in any more!

---------- Post added at 14:41 ---------- Previous post was at 14:39 ----------
tonyjandc said:
if you just got your nand x is should say v3 on the box if not the nand x needs updating but Mr modchips should sell you a v3 nand x . I live in London can program the board for you if you want .
Click to expand...
I already owed a Nand-X so with this order I bought the Nand-X to USB cable to update it to V3 which I have done successfully. Thanks for that offer but im currently only 16 and have no possible way of me getting upto you.
 
Y

Younge

VIP Member
May 27, 2010
143
0
T

tonyjandc

VIP Member
Dec 30, 2011
481
0
london uk
If you use nandpro thats the one I use make sure you have timing files installed and in nandpro double check port 95 installed . One of my pc's give me grief trying to program this board so I use my laptop instead . I found maybe its just me that having loads of usb appliances installed can be a pain . If you dont have access to another computer try removing some of your usb stuff and use the usb on the back of the pc . As I said this worked for me but not for everyone
 
D

danielh2k11

Junior Member
Feb 10, 2012
15
0
tonyjandc said:
If you use nandpro thats the one I use make sure you have timing files installed and in nandpro double check port 95 installed . One of my pc's give me grief trying to program this board so I use my laptop instead . I found maybe its just me that having loads of usb appliances installed can be a pain . If you dont have access to another computer try removing some of your usb stuff and use the usb on the back of the pc . As I said this worked for me but not for everyone
Click to expand...
Think you could maybe come on Team Viewer and help me out if you have some free time as I don't have a clue what 'Timing files' are to be honest.
 
T

tonyjandc

VIP Member
Dec 30, 2011
481
0
london uk
Im afraid time is not on my side as I have to goto work but to make life eaiser open nandpro folder and look to see if you have any files with .xsvf ending if not you will have to download these once downloaded open rar and transfer to nandpro folder. open nandpro and look for a text file named usage open this up and scroll to bottom change to falcon should read NandPro xsvf: falcon.xsvf copy this and now start nandpro shift right click (open command prompt here) now paste what you copied NandPro xsvf: falcon.xsvf this should program your coolrunner . It looks like you dont have timing files.
 
Y

Younge

VIP Member
May 27, 2010
143
0
tonyjandc said:
Im afraid time is not on my side as I have to goto work but to make life eaiser open nandpro folder and look to see if you have any files with .xsvf ending if not you will have to download these once downloaded open rar and transfer to nandpro folder. open nandpro and look for a text file named usage open this up and scroll to bottom change to falcon should read NandPro xsvf: falcon.xsvf copy this and now start nandpro shift right click (open command prompt here) now paste what you copied NandPro xsvf: falcon.xsvf this should program your coolrunner . It looks like you dont have timing files.
Click to expand...
this looks familar :rolleyes2: and yes he does have the timing files or it would be a different error
 
You must log in or register to reply here.