ANSWERED CoolRunner Green light doesn't light up

A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
So guys i ave done the RHG or so i think i have. I did everthing correctly, and all but now, my green light doesnt show up when i turn it on. It only appears a red light and no green light. What do you think is going wrong? Maybe some of the solder isn't working?

EDIT : Do you want me to post pics of the soldering? I know there is a thread similar, but mine is a Jasper 16 mb .
 
Last edited:
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
how should we know when you haven't postet any hires pic of your soldering ?
 
A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
OK here are the pics, i tryed to get the best shots of them . I already checked with a magnifier glass and there are no solder that is incorrect ( or so i think ) . I will let you guys decide that :

 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
just to make sure, have you programmed the cool runner with the right timing file ?

besides its seems like the solder point on the qsb at the hana chip dosen't make contact to the mainboard

and another thing, the capasitor you put on the cr board, remove it again, its normal only used for BB jasper board
 
Last edited:
A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
I did, i used the command :

" NandPro xsvf: Jasper.xsvf " and the green light in fact did turn off. So i guess its well programmed .What is the solder point in the QSB that you are talking about ? Its the one near R1 ?

And regarding the capacitator , so can i just cut one of the pin headers and it should disable him right?

Goldensavage, do you advice in putting the wires as they are in the pics? I though that we just could put them like i did that there were going to have no errors regarding the chip .
 
Last edited:
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
yes that is the point i'm talking about

why cut, why not just desolder it


and like Goldensavage says, try rerouting your wire like in the tut
 
Last edited:
A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
Ok i will, that will mean that i will have to resolder some wires. I will do that, but first will try to solder the point near the HANA chip and then if that doesnt work i will reoute the wires. Also, i already done with the guide, because i flashed the image and all , the chip only lights up red. Also, i found out that my xell turned up a blue screen with the usual lines does that mean anything also?
 
  • Like
Reactions: Heronimoh
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
if xell boots the cr is working
 
A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
The problem is that i did all of that mate. I flashed my nand as the final step. The problem is that i thought that i had a green light in the Cr when i turn it on for the shell so i continued until i flashed the nand. After flashing the nand, i just get a RED light and no green light. I confirmmed with a guy that was with me and he says that when i booted into xell he saw the green light but doesnt have sure. Also, now that i see the point near the HANA chip is cleary not soldered, so i will solder that and see what happens.
 
A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
the one indicated , the 360 multi builder. Everthing went smootly the programming of the cr and the nand dump with no bad blocks , i just dont know why there is no green light, but i will resolder that point near HANA and if that doesnt work i will try to rearrange the wires in the bottom

EDIT: And like i said, my screen of xell was not black but blue . That was the onle diference that i saw
 
Last edited:
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
if xell is booting the soldering most likely as it should be, try building a new nand file with multibuilder 0.7 and copy the freeboot file and xenon.elf to a usb stick, put it in your box and boot xell and let it install it
 
A

AMightyPancake

Junior Member
Dec 30, 2011
14
0
So what do you advice hackerjac ? From where do i start with this guide ? http://www.team-xecuter.com/forums/showthread.php?t=76193 .

Also, you say to " copy the freeboot file and xenon.elf to a usb stick, put it in your box and boot xell and let it install it " but in the guide i followed it says " Copy nandflash.bin and xenon.elf " . Maybe that's it ?


EDIT : And how can i boot xell, if now there is nothing on the screen. When i first power it up xell did boot, but now only the chips gets red and nothing else. Maybe is because of that point near the HANA chip?

EDIT 2 : From what i understand, i have to start from here , "Create your NAND Image" and forward
 
Last edited:
TilVl

TilVl

VIP Member
May 11, 2011
1,383
0
Your stby_clk is messed up. Check it. The one wire going to the hana

Sent from my SGH-T839 using Tapatalk
 
You must log in or register to reply here.