Coolrunner help...

P

psykix

Full Member
Oct 31, 2011
42
0
Wirral
FFS! Do you know how many times I looked at that!

Couldn't see the wood for the trees...

All working now :)

Thanks y'all for putting up with me!!
 
J

jhan1

VIP Member
Jan 13, 2011
223
0
Thanks all for this very informative thread. Your mistakes are something we can learn from. I do sh*t like that everyday :D
 
P

psykix

Full Member
Oct 31, 2011
42
0
Wirral
I've built an image with multibuilder, and flashed it back, reassembled the Xbox and it boots up fine..

Not sure what to do next, and I have noticed the cpu fan seems to be going full pelt too..
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
I have a question is there an alternate point for the B wire on phat console, I don't want to solder there cause it is a scary point to solder to
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
thanks guys so the B wires alternate point is R2R6?

---------- Post added at 10:45 ---------- Previous post was at 10:40 ----------

I mean above R2R6 LOL
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
OK thanks, i just wanted to use it cause i didn't want to solder onto the 3V trace on the motherboard cause of QSB using it
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
I am having no luck getting Coolrunner to work fan just keeps speeding up and down and no green led on Coolrunner
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
I can get Coolrunner to flash green when I write ecc image and boot Xell, and when I restore to original Nand. But after I write freeboot ggbuild image then Xbox won't boot and Coolrunner wont flash green anymore
 
M

mocalacace

Junior Member
Feb 6, 2011
21
0
digiman said:
I can get Coolrunner to flash green when I write ecc image and boot Xell, and when I restore to original Nand. But after I write freeboot ggbuild image then Xbox won't boot and Coolrunner wont flash green anymore
Click to expand...
Make sure you unplug your Xbox for 30 seconds after you flash the NAND
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
OK I will try that, forgot to mention when I restore nand back to original my xbox try's to boot then give 3 red lights. Is this related to me not reading my nand when I updated my dashboard to 13604. My original nand was dumped when I had 13599
 
digiman

digiman

Senior Member
Nov 2, 2011
185
0
I did the sync and eject buttons to see what the 3 red lights brang up and it was all 4 lights flashing, then 4 lights again, then 2 top lights, then 2 top lights

Error 0022

I have some led light mods installed (Led storm, to more sets of leds (blue) and a Talismoon Whisper Legacy with leds in it. Could this be the problem? it did boot into Xell after writing Ecc or does that have nothing to do with Coolrunner?
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
digiman said:
I did the sync and eject buttons to see what the 3 red lights brang up and it was all 4 lights flashing, then 4 lights again, then 2 top lights, then 2 top lights

Error 0022

I have some led light mods installed (Led storm, to more sets of leds (blue) and a Talismoon Whisper Legacy with leds in it. Could this be the problem? it did boot into Xell after writing Ecc or does that have nothing to do with Coolrunner?
Click to expand...
sounds like you are either flashing a bad nand over to xbox or your having a red light problem,and need reflow/reball.if it is true red ring,it would keep box from sending signal to anything,including the coolrunner,but if u flash a bad nand to an xbox it would also red ring.what kind of xbox is this and what are you using to flash and build nand?
 
You must log in or register to reply here.