That looks fake. Doesn't even have the little guy on the chip. http://team-xecuter.com/fake-xecuter-coolrunners-xecuter-unlocked-dg-16d4s-pcb-warning/
GENERAL Coolrunner LED Mod
- Thread starter superspeed
- Start date
RROD!
VIP Member
- Apr 13, 2011
- 786
- 0
you are the first i know of to say this is not working for on the slim i am not saying you are wrong just saying maybe there is a change in the slim the same as the phat where some use common ground and some common negative this is a young mod maybe we need to start posting pics of the rf we have and if it works or not and if also you can leave the console pluged in and put black probe to part of metal case and probe posi side of led and see what readings we get as this will show common live or ground? sound like a plan guys???
RROD!
VIP Member
- Apr 13, 2011
- 786
- 0
yer you pic is page 20 your model is 1410 wireless card the op is a 1409 would be great if we could get more guys to comfirm there models phats slims number or rev it seems slim rf 1409 works 1410 dont phats rev a and rev h dont but rev b works lol well thats what ive seen in this thread so far lol
(yes i can just about see digimans little man too )that sounds soooo wrong pmsl
(yes i can just about see digimans little man too )that sounds soooo wrong pmsl
Last edited:
Post a pic of the board in question and the work you've done. Instead of coming into and being all bad and mighty about you have 20 years experience blah blah blah. I've heard that story about a dozen times.
I have a total of 3 slims I can check the rf board rev on and test common lines (gnd and vcc)
I also have phat rf modules rev f, h, a, va, e, a-1-1, and b.
I will go through tonight and test them all on the same system to see what I can find.
RROD!
VIP Member
- Apr 13, 2011
- 786
- 0
that would be great thank you il crack open some slims tomoz and see what rf is in them and post back be nice to get this one nailed lol ive also made a post in the j runner thread asking if it would be possible to add a option for custom xsvf so see what happens there 
now now, no need to get snippy :tongue: higher post count doesn't mean you're any better, lol (btw - notice the smiley, text based communication is harder to convey sarcasm and just silly poking fun through and facial expressions. lmao)
A pic of the board is on pg 20, and I merely stated my experience as I know most ask "how long have you been soldering? are you new?" I am the first to admit I'm no expert, but I certainly know my way around an iron and PCB. as soon as I'm off work I can get pics of the CR and video of the RF in use.
Last edited:
After seeing the post with your RF board I have to withdraw my previous statements.
Looks like they did indeed change the RF board. I wasn't trying to be snippy its just been a very long day. I missed the post on page #20 which I can't monitor this thread 24/7 so accept my apology. I checked every single version of the phat RF boards that I have and not 1 had the common ground to any point on the led's. Let me ask you something the point you soldered that led to did you scratch it back to copper or was it an existing point.no apology needed sir, I didn't take offense :biggrin:After seeing the post with your RF board I have to withdraw my previous statements.
I scratched the coating back to get to the gnd. I found a sweet spot for the phat boards that is an existing point where we should be able to get a 0603 led in without needing to modify the rf clip/cover for the #3 (bottom right when horizontal) spot
will do! only 2.25 hrs of my shift and I can work on it.
Sorry if it's hard to read, the image should link to the full size pic.
Red shows the area the GND points are
Orange would be how the led can be placed to clear without having to modify the ROL cover
Blue is where the actual GND vias are that would be used
Last edited:
Hey guys. I did this mod earlier tonight using the controller 4 led and everything went fine. But what I'm wondering is, is there a way to wire it so that you can make all 4 quadrants flash at once?. I tried wiring it with 2 wires and 2 diodes running off the 68ohm resistor on the CR and it DID make the 2 quadrants flash properly but it would only glitch a couple times and then stop. So I'm assuming that wiring it that way is a no go as it must be pulling too much power away from the CR or something. BTW this is on a SLIM.
Another version of this mod I'm wondering is possible is to wire it in such a way that the middle red led will flash while debugging but at the same time the middle green light gets turned off when the red turns on and vise versa? I tried wiring it to just the red led and it wouldn't even turn on. Wondering if it has something to do with the green (left led) being on at the same time?
Another version of this mod I'm wondering is possible is to wire it in such a way that the middle red led will flash while debugging but at the same time the middle green light gets turned off when the red turns on and vise versa? I tried wiring it to just the red led and it wouldn't even turn on. Wondering if it has something to do with the green (left led) being on at the same time?
I'm telling you. LoL way more popular than I expected. I wonder since TX was incorporating this into the next gen chips if they will be able to get the current led's on all version RF boards without adding extra ones.wow this is very popular mod
Thanks to everyone who has contributed to this small but popular mod. All you're input and help along the way is grwatly appreciated.