Coolrunner light blinks green slowly never glitch's?

D

DeathGrin

Full Member
Aug 4, 2011
26
0
Hey all,

I am sorry for posting about this again because i am sure it has been posted but i couldnt find one.

Anyways, i installed the coolrunner, programmed it with falcon timing file, made sure all my soldering was good.

read nand twice, they matched, made eccglitch and wrote it to nand.

well when i turn the xbox on now to get my cpu key and dvd key but the coolrunner never glitches the system, the red light is on and then the green light blinks very slowly.

any help would be very appreciated! thank you in advance!
 
E

esbmaepo

VIP Member
Oct 2, 2011
461
48
Esbjerg - Denmark
DeathGrin said:
Hey all,

I am sorry for posting about this again because i am sure it has been posted but i couldnt find one.

Anyways, i installed the coolrunner, programmed it with falcon timing file, made sure all my soldering was good.

read nand twice, they matched, made eccglitch and wrote it to nand.

well when i turn the xbox on now to get my cpu key and dvd key but the coolrunner never glitches the system, the red light is on and then the green light blinks very slowly.

any help would be very appreciated! thank you in advance!
Click to expand...
Most likely your wire positions.

You shouldn't have any problems with Falcons, they are the easiest to work with.;)
 
D

DeathGrin

Full Member
Aug 4, 2011
26
0
Will post pictures in the morning, and i also kind of forgot to mention that i messed up the standby point that you solder to with the orange cable. so i had to try the alternate point for it on the underside of the mobo and then screwed up the freakin alternate point. ripped up the trace that went from the alternate point to the other point. so i had to solder a wire to those two points. i will just post pics in the morning it will be easier to show you guys
 
D

DeathGrin

Full Member
Aug 4, 2011
26
0

Shot at 2011-12-13


Shot at 2011-12-13


Shot at 2011-12-13


Shot at 2011-12-13


Shot at 2011-12-13
 
Goldensavage

Goldensavage

VIP Member
Jul 26, 2009
3,332
0
Essex, UK
Falcons are by far the easiest to glitch. Mine glitches every time within 2-5 seconds.

Yellow wire is completely on the wrong point

Judging by the first pic, i would say you have ruined that particular resistor. Too much heat.

Did you use flux?

Also the second picture (Green Wire) looks like it just a big ball of solder. There could be multiple bridges on it.

The 4th picture, again looks like a very dry joint. Needs clearing, flux and re-solder.

The fifth is not to bad.

I would say it is a serious soldering issue.

Just noticed, why is the blue wire in the picture three times on the third picture. And going round the x clamps?????



This is how it is supposed to go
 
Last edited:
S

stred

Junior Member
Jul 17, 2010
22
0
for a start you have soldered the yellow wire to the wrong spot, should be at ft6u7 mate
 
gargoyle67

gargoyle67

VIP Member
Feb 4, 2011
231
0
Read install tut glitch fail :facepalm: like Goldensavage said that resistor looked damaged, I'd de-solder every thing and clean up the board, Then see if your 360 still works. I don't mean to flame...But I don't think you have the skill set to attempt something like this, Best advice if your machine still works, Give it to someone who's done rgh\jag before (successfully)
 
D

DeathGrin

Full Member
Aug 4, 2011
26
0
haha wow, i feel like an idiot for putting the yellow wire to the wrong point, and yea i really messed up soldering, i didnt have a light and was using very little, my own stupid fault. thanks though guys
 
You must log in or register to reply here.