coolrunner timing files

N

N.E.Modz

VIP Member
Sep 27, 2009
2,285
68
A.K.A daleh43

Attachments

X

XeXDevelopers

Full Member
Jul 19, 2014
34
0
N.E.Modz said:
you dont need nandpro3 anymore, just use JRunner:


- - - Updated - - -



you dont need nandpro3 anymore, just use JRunner:
Click to expand...
When i click program coolrunner the box that pops up i can click on anything and also my jr programmer v2 is pluged in

- - - Updated - - -

N.E.Modz said:
you dont need nandpro3 anymore, just use JRunner:


- - - Updated - - -



you dont need nandpro3 anymore, just use JRunner:
Click to expand...
When i click program coolrunner the box that pops up i can click on anything and also my jr programmer v2 is pluged in
 
N

N.E.Modz

VIP Member
Sep 27, 2009
2,285
68
A.K.A daleh43
when you've dumped nand x 2 you can choose either rgh/rjtag and which dash you want to choose. when you click on prog coolrunner it will highlight either rgh column or rgh2 column. choose which board you have the click program cr

Make sure you have the power disconnected from console
 
X

XeXDevelopers

Full Member
Jul 19, 2014
34
0
N.E.Modz said:
when you've dumped nand x 2 you can choose either rgh/rjtag and which dash you want to choose. when you click on prog coolrunner it will highlight either rgh column or rgh2 column. choose which board you have the click program cr

Make sure you have the power disconnected from console
Click to expand...
My coolrunner is not even on my xbox yet i was told that i should program it before i install it on the xbox

you have aim or skype?
 
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,146
0
Borås, sweden
you need to pick your hack-method first (JTAG/RGH/RGH2) and then you get to pick your timing file. and for the record, you can program the chip while its installed, just as long as you dont power the motherboard while doing so.
 
X

XeXDevelopers

Full Member
Jul 19, 2014
34
0
Antalpromille said:
you need to pick your hack-method first (JTAG/RGH/RGH2) and then you get to pick your timing file. and for the record, you can program the chip while its installed, just as long as you dont power the motherboard while doing so.
Click to expand...
thank you also where is jbc1 i cant seem to find it for the cpu_rust
 
X

XeXDevelopers

Full Member
Jul 19, 2014
34
0
Antalpromille said:
you need to pick your hack-method first (JTAG/RGH/RGH2) and then you get to pick your timing file. and for the record, you can program the chip while its installed, just as long as you dont power the motherboard while doing so.
Click to expand...
i have found it its on right side near the gpu/cpu and also when i click program coolruuner this is all that comes up

http://gyazo.com/53fd1fc6c3a4189dc42c422f8f9660ff
 
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,146
0
Borås, sweden
Becouse you have retail selected. Select what exploit you are using, just as i said.
 
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,146
0
Borås, sweden
XeXDevelopers said:
Okay thanks and also the ecc is the timing file right? because this video the dude click crate ecc and it went but mine says chose file
Click to expand...
No, the timing files are the timing files. The ECC is what you use to initially boot to Xell to get your cpu-key. the ECC is created from your original nand-dumps when you have them.Time to start Reading and searching.
 
X

XeXDevelopers

Full Member
Jul 19, 2014
34
0
Antalpromille said:
No, the timing files are the timing files. The ECC is what you use to initially boot to Xell to get your cpu-key. the ECC is created from your original nand-dumps when you have them.Time to start Reading and searching.
Click to expand...
i got it i reshared why and i have installed the coolrunner programed it created the ecc and writen it anything els im missing?
 
You must log in or register to reply here.