ANSWERED CoolRunner won't program

[legitmod]

Ok i am trying to program a friends coolrunner but i keep getting this error

Looking for usb interface device
Compression InSize:0x593E OutSize:0x2832
Arm Version:0003
Sending compressed data:0x2832 bytes
Executing File
File execution FAILED! Status :0x0002

could some one give me some insight on what could be going wrong.......an to make sure i am right to extract a good nand the command for a falcon is nandpro usb: -r16 nand1.bin....:facepalm:

 

[Martin C]

What lights do you have on the coolrunner? Did you make sure you plugged the NAND-x to Coolrunner cable correctly?

 

[legitmod]

yep its a green light an red not programed

 

[Martin C]

So what command are you running?

 

[legitmod]

NandPro xsvf: Falcon.xsvf is this wrong???

 

[Martin C]

Nope, looks ok. Have you got the CR set to PRG? Have you programmed one before? Is the programmer correctly inserted in the NAND-x?

 

[legitmod]

yep i sure have an have never had this problem be4 i guess you always run into some thing an its set to phat program an still get the error inserted right an every thing could the coolrunner be bad

 

[axee44]

Bit of a long shot but worth checking.
www.team-xecuter.com/forums/showthread.php?t=79081

 

[legitmod]

Bit of a long shot but worth checking.
www.team-xecuter.com/forums/showthread.php?t=79081

nope its not fake got it from xconsoles

 

[legitmod]

Nope, looks ok. Have you got the CR set to PRG? Have you programmed one before? Is the programmer correctly inserted in the NAND-x?

IDK do you think the coolrunner could be faulty an can i use this command instead
NandPro jed: falcon.jed

 

[axee44]

Did you try writting different .xsvf file??

 

[legitmod]

Did you try writting different .xsvf file??

yep an get the same error:facepalm:

 

[Martin C]

Is this the very first time this has been attempted with this Coolrunner? Do you have another you can try?

 

[spookyman166]

have you plugged in the right way? Ie the red wire is on the VCC pin...

 

[legitmod]

have you plugged in the right way? Ie the red wire is on the VCC pin...

yes cause if it was pluged in wrong the coolrunner would not have both lights on

Is this the very first time this has been attempted with this Coolrunner? Do you have another you can try?

yep the first time on this coolrunner an no i am out of stock at the moment this is my last on an i tried diffrent files to an get this

C:\nandpro>NandPro xsvf: Falcon.xsvf
NandPro v3.0a by Tiros

Looking for usb interface device
Compression InSize:0x593E OutSize:0x2832
Arm Version:0003
Sending compressed data:0x2832 bytes
Executing File
File execution FAILED! Status :0x0002

C:\nandpro>NandPro xsvf: Trinity.xsvf
NandPro v3.0a by Tiros

Looking for usb interface device
Compression InSize:0x593E OutSize:0x2B50
Arm Version:0003
Sending compressed data:0x2B50 bytes
Executing File
File execution FAILED! Status :0x0002

C:\nandpro>NandPro xsvf: .xsvf
NandPro v3.0a by Tiros

Looking for usb interface device
Couldn't open file
Error: Can not continue!

C:\nandpro>NandPro xsvf: opus.xsvf
NandPro v3.0a by Tiros

Looking for usb interface device
Compression InSize:0x591C OutSize:0x2874
Arm Version:0003
Sending compressed data:0x2874 bytes
Executing File
File execution FAILED! Status :0x0002

:facepalm:

 

[Martin C]

Check over the Coolrunner to make sure there's nothing visibly wrong.

 

[legitmod]

Check over the Coolrunner to make sure there's nothing visibly wrong.

yep its plugged in correct the switch is at program an phat but my friend told me he plugged it in wrong the first time be4 he plugged it in right could that had damaged the coolrunner or would it have damaged the nandx first cause i can still read his nand with his nandx cause its setting right in front of me

 

[axee44]

Same problem and possible solution.
www.team-xecuter.com/forums/showthread.php?t=79336&highlight=File+execution+FAILED!+Status+:0x0002

Yet again worth checking.

 

[Martin C]

yep its plugged in correct the switch is at program an phat but my friend told me he plugged it in wrong the first time be4 he plugged it in right could that had damaged the coolrunner or would it have damaged the nandx first cause i can still read his nand with his nandx cause its setting right in front of me

There you go.

What do you think happens if you try to send 3.3v down a data line?

Yep, something's been blown.

 

[legitmod]

There you go.

What do you think happens if you try to send 3.3v down a data line?

Yep, something's been blown.

thats what i thought cause i checked all wires an every thing an got the same thing well guess i'll be ordering a new one for him hey c martin i have a noter issue also should i just make a new thread or talk about in this one