Corona V2 4GB wont glitch

M

m37r01d

Full Member
Oct 14, 2011
35
8
Im trying to get this v2 to boot xell to retrieve the DVD key to install an ****

i've read the nand and created an ECC and flashed it (flashed a few times)

Checking Files
Finished Checking Files
Corona 4GB Manually Selected
Checking Console..
Device Not Found.
Can not continue
E:\
Reading from E:\ to C:\Users\M37R01Dz\Desktop\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Done!
in 4:45 min:sec
Initializing nanddump1.bin..
Corona 4GB
Glitch2 Selected
CR4 Selected
ECC created
Writing to E:\ from C:\Users\M37R01Dz\Desktop\J-Runner v3 (5) Core Pack\output\image_00000000.ecc
Done!
in 0:01:194 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished

--------------------------------------------------

I've tried different wire lengths for the cpu_rst from 10cm upto 55cm and coiled it around the heatsink
i have dip 8 on and tried dip 3-6 on and off
I've tried all 3 jumper settings
I can hear it resetting but just cant get it to boot xell,
I've left it on for 10-30 mins on just about every setting i can think of
I've also tried the alternate points for the cpu_rst line with no luck
any ideas would be appreciated.
 
Last edited:
Titanfreak736

Titanfreak736

BANNED
Oct 19, 2014
194
0
jesus christ we need pictures make sure you tick cr4 in jrunner and if it has winbound memoryteam-xecuter-xell-on-the-new-corona-v6.jpgclick on patches/dashlaunch and then in wonbound select wb for non 4gb and wb4g if it has 4gigs like yours and then rewrite
 
Last edited:
M

m37r01d

Full Member
Oct 14, 2011
35
8
Last edited:
M

m37r01d

Full Member
Oct 14, 2011
35
8
briggs01 said:
correct mate it is an alt , some people get better results
can you post pics of all your solder points please , are you sure your corona is E , and try loading the ecc manually into source
Click to expand...
I'm not sure what you mean by am I sure my corona is E?
It has the small chip on the topside where the nand chip normally would be which from the diagram I've seen indicates it's a v2.
 
B

briggs01

VIP Member
Feb 17, 2013
1,324
0
m37r01d said:
I'm not sure what you mean by am I sure my corona is E?
It has the small chip on the topside where the nand chip normally would be which from the diagram I've seen indicates it's a v2.
Click to expand...
in jrunner it should say something like 3588 for your corona
 
M

m37r01d

Full Member
Oct 14, 2011
35
8
i have a 2nd v2 corona that i installed exactly the same and was giving the same issue
i played more with the wire length of the cpu_rst wire and cut it down to about 2 inches and set dip 2 and 8 on, and was able to glitch both boxes with glitch times from 1-4 resets
thanks for the help everyone ;-)
 
B

briggs01

VIP Member
Feb 17, 2013
1,324
0
m37r01d said:
flashed back to stock and removed the cr4 and it booted right up

- - - Updated - - -when you

not sure where it should say that but i didnt see 3588
Click to expand...
when you try to read the nand you should get a pop up window on the right hand side that shows your drives connected to your pc E.G C drive , d drive for you writer , then E your corona board usually says 3588 next to it
 
M

m37r01d

Full Member
Oct 14, 2011
35
8
briggs01 said:
when you try to read the nand you should get a pop up window on the right hand side that shows your drives connected to your pc E.G C drive , d drive for you writer , then E your corona board usually says 3588 next to it
Click to expand...
Oh yea thats the size or something but yea it displayed the size, thats how i was able to read and write to it
but i was able to get them all sorted out, again thanks for the help
 
You must log in or register to reply here.