Corona V3 with installed CR4 won't glitch

L

Loki999

Noob Account
Apr 25, 2015
5
0
Console Type: Corona v3
Programmer Used: JRP v2.0
NAND Size: 16
Dashboard version: don't know and doesn't really matter to the problem
Screenshot of NAND details from J-Runner: j-runner.png
J-Runner log: Initializing nanddump1.bin..Corona
Nand Initialization Finished
ECC created
Version: 10
Flash Config: 0x00043000
Writing Nand
image_00000000.ecc
Done!
in 0:18 min:sec


Version: 10
Press Escape to exit
Waiting for POST to change
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D

Image of the CR4 XL
Images of close-up soldering to motherboard (attach images to your post)
Was the console working before you started: Y
Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: Y
How long is the light on for each time? Its blinking.



Hey Guys, i've tried everything to get this bastard to glitch, but it always stops at Post 0D. I already tried 3 different CPU_RST points, changed my cable to the shieled one and resoldered all my points already (pic of the soldering coming up tomorrow, need daylight to take better pictures). Do you guys have any idea what i could try next? or what i missed out?

Would be really happy, if you could help me out here ;)

Greets, Loki999
 
B

briggs01

VIP Member
Feb 17, 2013
1,324
0
as mentioned above you need pics of soldering , but first question is , did you check if you have traces for post fix , because v3 usually needs a post fix adaptor
 
D

Dadko

VIP Member
Apr 2, 2015
209
23
Check if your postfix adapters pogo stick fitting properly under cpu. I had few cases, when I had to push it a little
 
L

Loki999

Noob Account
Apr 25, 2015
5
0
Don't know what exactly happened to this one, but as you can see on the last picture, i reinstalled it. It may have went off, when i reinstalled the postfix adapter the first time.

To the pogo stick: how far has it to be under the cpu? If i stick it farther in, the fixing clamp on the other side falls off.
 
Last edited:
john mathews

john mathews

VIP Member
Jan 3, 2014
2,551
88
peoria illinois
k have u tried dips 2-8 4-8 etc and 10 ohms or 100 ohm on postbit and I would take that dlb cable off used standard wire under xclamp short as possible - exactly all wires short as possible never had issue with slims
 
Last edited:
L

Loki999

Noob Account
Apr 25, 2015
5
0
Hey guys, i don't really know why, but it works now, tried another dip setting, again, but now it worked out. Now set to 1-8 and 10 Ohm.

Thanks for helping me out here ;)
 
L

Loki999

Noob Account
Apr 25, 2015
5
0
Yeah, tried those settings before, but maybe it didn't glitch then, because of the desoldered cap
 
You must log in or register to reply here.