CORONA Corona V3 won't boot xell

brihaupt · Dec 11, 2014

I have a Corona V3 which I've installed a CR4 XL, QSB, and J-R Programmer V2. I've had results matching http://team-xecuter.com/forums/show...te-cycles-no-Xell&highlight=Corona+won't+xell

I've double-checked all of my solder points and they are all good. This board has all of the POST Points and required no POSTS hardware.

I apologize if I've neglected information; this is my first post PLEASE bare with me. Attached are pictures and screen shots.

Monitoring POSTS:
Version: 10
Press Escape to exit
Waiting for POST to change
Post 10 - Payload/1BL started
Post 0C
Post 0D
Post 0E
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Done!

chase · Dec 11, 2014

corona v3 has no post out.. you need the postfix adapter

can you post pic to show it has post out

also show a close up of the nand qsb and the nand area

brihaupt · Dec 11, 2014

Thank you for your response. I am fairly sure it is a V3 with the Posts_Out. I used http://www.maxconsole.com/maxcon_fo...rona-Motherboard-Identification-amp-Solutions to identify my board based on the ST NAND I concluded it was a V3. I apologize for the QSB resistors not being clear but R2C4, R2C7, R2C6, andR2C10 all have resistors.

brihaupt · Dec 11, 2014

I just found http://team-xecuter.com/xecuter-official-corona-motherboard-identification-solutions/ indicating that I probably have a Corona V1. I will check my install vs Corona V1 and post an update.

brihaupt · Dec 11, 2014

Checked the install guide for V1 which seems to be what I have and the install is correct for this version.

GeekHeat · Dec 11, 2014

Looking at your j runner PIC. U didn't select cr4 in xebuild tab.

brihaupt · Dec 11, 2014

I rewrote the ECC ensuring that CR4 was selected. No change. I've tried setting DIP 1 and 8 instead of 3 and 8 as Poster of http://team-xecuter.com/forums/show...te-cycles-no-Xell&highlight=Corona+won't+xell had success with. No change for me.

01DawG10 · Dec 11, 2014

briha Corona V3 which I've installed a CR4 XL said:
http://team-xecuter.com/forums/showthread.php?148035-Corona-V3-CR4-XL-infinite-cycles-no-Xell&highlight=Corona+won%27t+xell[/URL]

I've double-checked all of my solder points and they are all good. This board has all of the POST Points and required no POSTS hardware.

I apologize if I've neglected information; this is my first post PLEASE bare with me. Attached are pictures and screen shots.

Monitoring POSTS:
Version: 10
Press Escape to exit
Waiting for POST to change
Post 10 - Payload/1BL started
Post 0C
Post 0D
Post 0E
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Done!

When you used Rater, did you select the CR4 button? The option is not selected by default. These dont look like the normal output for CR4. Please note, the selection in Rater, not Jrunner main window..

xximod4uxx · Dec 11, 2014

Does it just glitch forever?

chase · Dec 11, 2014

your soldering isn't the greatest but it also isn't the worst.. all I can say is go through all the dips + leave dip 8 on.. you may also want to try the postbit jumper in all 3 positions starting with default..

if nothing is works and you're sure your soldering is ok, then I would flash the ecc from the MAGIC file set and see if that works

brihaupt · Dec 11, 2014

The ECC I'm using is from the MAGIC file set. Is there a different ecc I could be using?

chase · Dec 11, 2014

brihaupt said:
The ECC I'm using is from the MAGIC file set. Is there a different ecc I could be using?

you can use the create ECC button within j-runner .. since j-runner has been updated recently, the ecc will be the same as the magic one

the only thing left would be your soldering, postbit jumper and dip switches

can you also post your complete j-runner log pls

brihaupt · Dec 11, 2014

xximod4uxx said:
Does it just glitch forever?

Yes. Green light on the CR4 blinks every 5ish seconds.

brihaupt · Dec 11, 2014

01DawG10 said:
When you used Rater, did you select the CR4 button? The option is not selected by default. These dont look like the normal output for CR4. Please note, the selection in Rater, not Jrunner main window..

I didn't use Rater. I will later today and post results.

brihaupt · Dec 11, 2014

Rater output per request. I so far have gone through dip 1/8 through 7/8 on one jumper setting only. I did get some that said glitch successful and then right back into the loop.

jekdyell · Dec 11, 2014

Try dips 8&2 & postbit 0ohm or 10ohm.

brihaupt · Dec 12, 2014

I tried all dip settings 0-7 leaving 8 on with all postbit settings. Rater outputs are the same as previously posted. Reading the NAND now shows

Checking Files
Finished Checking Files
Version: 10
Flash Config: 0x00043000
00043000
Corona
CB Version: 9188
Trinity
Reading Nand to C:\Program Files\J-Runner\output\nanddump1.bin
Reading Nand
Done!
in 3:36 min:sec

Reading Nand to C:\Program Files\J-Runner\output\nanddump2.bin
Initializing nanddump1.bin..
Header is wrong..
Trinity
RGH2 Selected
Nand Initialization Finished
Reading Nand

I tried setting my system back to retail and removing 5V but that doesn't boot properly.

chase · Dec 12, 2014

I hope you backed up your original nand before reading the nand again.. its easy to overwrite the nand and loose if forever

what you should have done was install the CR4 to the other side of the southbridge ..that would have shortened the cpu_rst and postout wire as short as possible just like the install guide

if ECC was flashed correctly and you say you've gone through all the dip/jumper options, then the only thing left would be the soldering

brihaupt · Dec 12, 2014

chase said:
I hope you backed up your original nand before reading the nand again.. its easy to overwrite the nand and loose if forever

what you should have done was install the CR4 to the other side of the southbridge ..that would have shortened the cpu_rst and postout wire as short as possible just like the install guide

if ECC was flashed correctly and you say you've gone through all the dip/jumper options, then the only thing left would be the soldering

I did backup my original files. I have them in at least four different places on two separate computers. I will work this weekend on resoldering and relocating the CR4. The install guide http://team-xecuter.com/forums/showthread.php?147807-CR4-XL-SLIM-Corona-v1-v2-Install-Guide-(RGH2-) shows the CR4 in the same location I put it.

brihaupt · Dec 12, 2014

chase said:
you can use the create ECC button within j-runner .. since j-runner has been updated recently, the ecc will be the same as the magic one

the only thing left would be your soldering, postbit jumper and dip switches

can you also post your complete j-runner log pls

===================================================
Monday, December 08, 2014 9:47:51 PM

J-Runner v0.3 Beta (5) Started

Version v0.3 Beta (6) is available for download.
Checking Files
Downloaded *xeBuild/options.ini
Downloaded *xeBuild/readme.txt
Downloaded *xeBuild/launch.xex
Downloaded *xeBuild/lhelper.xex
Downloaded *xeBuild/xeBuild.exe
Finished Checking Files
Downloading...

===================================================
Monday, December 08, 2014 9:49:51 PM

J-Runner v0.3 Beta (6) Started

Checking Files
Finished Checking Files

===================================================
Monday, December 08, 2014 9:50:19 PM

J-Runner v0.3 Beta (6) Started

Checking Files
Finished Checking Files
Corona Manually Selected

Bootloader Attached
Bootloader Version: 1.0.5
Device not found.

===================================================
Monday, December 08, 2014 9:57:31 PM

J-Runner v0.3 Beta (6) Started

Checking Files
Finished Checking Files

Erasing Flash ...
Writing Flash: ..............................................................................................
Done!
Verifying Flash: ..............................................................................................
Write Verified!
Restarting Device ...
Finished!

Bootloader Removed.
RGH Selected
Downloading SystemUpdate_17148_USB.zip
Done

Bootloader Attached
Bootloader Version: 1.0.5

===================================================
Tuesday, December 09, 2014 12:37:14 PM

J-Runner v0.3 Beta (6) Started

Checking Files
Finished Checking Files

Erasing Flash ...
Writing Flash: xxxxxxxx
Bootloader Attached
Bootloader Version: 1.0.5
xxWrite Failed

===================================================
Tuesday, December 09, 2014 12:45:53 PM

J-Runner v0.3 Beta (6) Started

Checking Files
Finished Checking Files
Version: 10
Flash Config: 0x00043000
00043000
Corona
CB Version: 13181
Corona
Reading Nand to C:\Program Files\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 3:29 min:sec

Reading Nand to C:\Program Files\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Corona
RGH2 Selected
Nand Initialization Finished
Reading Nand
Done!
in 3:28 min:sec

Reading Nand to C:\Program Files\J-Runner v3 (5) Core Pack\output\nanddump3.bin
Comparing...
Nands are the same
Reading Nand
Done!
in 3:28 min:sec

Reading Nand to C:\Program Files\J-Runner v3 (5) Core Pack\output\nanddump4.bin
Comparing...
Nands are the same
Reading Nand
Done!
in 3:28 min:sec

Comparing...
Nands are the same
Connection TimeOut
Initializing nanddump1.bin..
Corona
Nand Initialization Finished
Connection TimeOut
Connection TimeOut
CR4 Selected
Starting Read - please wait......
Connection TimeOut
ECC created
Version: 10
Flash Config: 0x00043000
Writing Nand
image_00000000.ecc

Version: 10
Press Escape to exit
Waiting for POST to change
Post 08
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D

===================================================

Search

Search

CORONA Corona V3 won't boot xell

brihaupt

Junior Member

chase

brihaupt

Junior Member

brihaupt

Junior Member

brihaupt

Junior Member

GeekHeat

brihaupt

Junior Member

01DawG10

Full Member

xximod4uxx

Full Member

chase

brihaupt

Junior Member

chase

brihaupt

Junior Member

brihaupt

Junior Member

brihaupt

Junior Member

jekdyell

Senior Member

brihaupt

Junior Member

chase

brihaupt

Junior Member

brihaupt

Junior Member