CORONA V5 HELP CR3 PRO V3/V4

chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
Version: 10
Flash Config: 0x00043000
00043000
Corona
16mbs
CB Version: 13121
Corona V5
dash:16747
mfg: 09/14/2013
was working before? yes

nand had one bad-block but j runner remapped the bad block immediately after dumping.
the bad block was at:

Bad Block ID @ 0x9 [Offset: 0x25200]
Bad Block ID @ 0x9 Found @ 0x3FF[Offset: 0x107BE00]
i have tried all day to upload images here but i think service provider saver has issues with TX site.
the machine was okay but it took me time to boot xell and when i got the cpu, i flashed updflash.bin
back and tried all combinations but the console glitches but no boot even the rater readings are wrong
thats when i thought i miss something...i need help to get a perfecto boot, she booted once but
even the controllers were not working.
please help me
http://2imgs.com/3abe4963b0
http://2imgs.com/7efa0d27f4
http://2imgs.com/6feb1c36e5
http://2imgs.com/8236c1eb38



Code: 
Slim Selected
Version: 10
Power Up
Waiting for POST to change
Post 01 
Post 03 
Post 04 
Post 05 
Post 06 
Post 07 
Post 08 
Post 09 
Post 0A 
Post 0B 
Connection Error
Post 01 
Post 03 
Post 04 
Post 05 
Post 06 
Post 07 
Post 08 
Post 09 
Post 0A 
Post 0B 
Shutdown
Slim Selected
Version: 10
Power Up
Waiting for POST to change
Post 01 
Post 03 
Post 04 
Post 05 
Post 06 
Post 07 
Post 08 
Post 09 
Post 0A 
Post 0B 
Post 01 
Post 03 
Post 04 
Post 05 
Post 06 
Post 07 
Post 08 
Post 09 
Post 0A 
Post 0B 
Post 01 
Post 03 
Post 04 
Post 05 
Post 06 
Post 07 
Post 08 
Post 09 
Post 0A 
Post 0B 
Shutdown
 
Last edited:
G

gavin_darkglide

VIP Member
Dec 14, 2012
2,303
118
Just looking at the pictures I would say that your soldering could be cleaned up a bit. Also have you tried using caps?
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
gavin_darkglide said:
Just looking at the pictures I would say that your soldering could be cleaned up a bit. Also have you tried using caps?
Click to expand...
i have tried all caps, wright now i'm writing back stock to see if it boots up well, but i have tried all the guide say.
it works well on stock but when hook up the cr3 pro, it just glitches while it makes
some sound.
i have a chip that failed to work on phat(r-jtag) but when you change it consoles work
unfortunately i have only 1 chip(cr3 pro v3/v4) only but i dont see what i have done wrong! wiring is fine
 
Last edited:
xzanox

xzanox

VIP Member
Nov 1, 2011
905
48
Netherlands, 1336
I sincerely agree with Gavin, it is probably very likely, that your soldering is causing this issue. Good connections are a must to glitch good, and looking at your solder points, they are all, a little off (messy, not shiny, not nice and round).

So my advice would be flux up everything and redo the points. Then try again, I'm almost certain it will help you.
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
xzanox said:
I sincerely agree with Gavin, it is probably very likely, that your soldering is causing this issue. Good connections are a must to glitch good, and looking at your solder points, they are all, a little off (messy, not shiny, not nice and round).

So my advice would be flux up everything and redo the points. Then try again, I'm almost certain it will help you.
Click to expand...
as i'm waititng for a nice camera to take new pics, i have removed all the wires and soldered a nandx/cr qsb with a lot of flux,(please i'm waiting for a nice camera) i'm going to upload the images. but i still get the same thing.
another thing, i removed the small sticker where the the final installation cable is put, the sticker had
'cr3 pro v1.0s corona v3/v4'' but under it on the chip it had ''cr3 pro v1.0s full post'',
i bought it from a trusted reseller and i'm not sure if its not a corona v3/v4 but just wanted you to know
also on the big black IC in the chip it has another V3/V4 sticker. but the chip has failed to boot normally.
i has only booted twice after 3 days and when it does, controllers dont work. could the the chip be one for the trinity & corona v1&v2 or ???
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
can anybody confirm if the chip i have is a FULL POST or FAKE POST, the images i posted show my installation and after
failing to boot normally with the chip i removed the sticker like mentioned in the above post.
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
alexander_1333 said:
This is normal.
Click to expand...
yup,as both cr pro chips full post and fake just use diff code,hardware is same,so made no sense to make a whole new batch when they could more cost effectivley flash v3/v4 code to full post boards and put stickers on em.
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
seriously what could be wrong with my chip. it managed to boot xell and after that there no is smile. i hope i can find what to use this chip for. i tried on trinity, it cant even boot xell on corona v5, booted xell and stopped there. i have done a good installation but it looks like my chip is sleeping. it glitches but no booting. i miss Martin C. he could have at-list told me what causes this
 
Last edited:
S

stucknvegas

VIP Member
Oct 25, 2012
656
0
Cypress CA. USA
Your CPU rst wire at point C-5r11 is scary looking.. Just like Galvin stated you need to improve your soldering. Cut down the exposed wire at most of the connections The chances of the chip being bad very little
I cant see your Small E and F bridges I know they are there otherwise you would not have your CPU KEY.. Check all points to ground with Multy meter
Remove the Yellow post out wire from post fix adapter Test any point on the fix to ground Set the meter to times 20 you should see 0.60 or close to that.. Test E and F as well
Remove wires from E and F from the pro chip Test from the wire to the small bridges you made the side away from the QSB If the console booted to the RGH Image a couple times and
controllers would not sinc!!! I would put retail Image back on first thing Test it with a wired controller as well
Onr more thing you need to bridge R2c4 for Rater to work read the install guide again please
 
Last edited:
You must log in or register to reply here.