RGH Corona V6 Glitch then red light

[daman10]

TX Product(s) used: Nand X, CR3 Lite
Console Type: Corona V6
Dashboard version: 16547
CB version: 13182
Screenshot of NAND details from J-Runner:

J-Runner log:
===================================================
Sunday, 29 June, 2014 9:19:22 PM


J-Runner v0.3 Beta (4) Started






Checking Files
Finished Checking Files
Version: 03
Flash Config: 0x00043000
00043000
Corona
CB Version: 13182
Corona
Reading Nand to C:\Users\Administrator\Desktop\Console Stuff\Xbox 360\RGH\J-Runner\J-Runner v02 (271) Core Pack\output\nanddump1.bin
Reading Nand
Error: 254 reading block 250
Done!
in 2:04 min:sec


Reading Nand to C:\Users\Administrator\Desktop\Console Stuff\Xbox 360\RGH\J-Runner\J-Runner v02 (271) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Corona
Reading Nand
RGH2 Selected
Nand Initialization Finished
Error: 254 reading block 250
Done!
in 2:04 min:sec


Comparing...
Bad Block ID 0250 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 0250 [Offset: 0x98A000]
Bad Blocks Remapped
Bad Block ID 0250 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 0250 [Offset: 0x98A000]
Bad Blocks Remapped
Nands are the same
Programming Coolrunner
C:\Users\Administrator\Desktop\Console Stuff\Xbox 360\RGH\J-Runner\J-Runner v02 (271) Core Pack\common\xsvf\corona.1_3.xsvf
Version: 03
Flashing C:\Users\Administrator\Desktop\Console Stuff\Xbox 360\RGH\J-Runner\J-Runner v02 (271) Core Pack\common\xsvf\corona.1_3.xsvf to CoolRunner
Input Filesize: 593E
Output Filesize: 2CE4
Done!


ECC created
Version: 03
Flash Config: 0x00043000
Writing Nand
image_00000000.ecc
Done!
in 0:10 min:sec
updflash.bin log (if applicable):
Image of Coolrunner:

Images of close-up soldering to motherboard:


Description of problem:

When i try boot to get Xell as soon as the glitch light flashes the console turns off with red light 0010

Was the console working before you started: Y

 

[alexander_1333]

Try a diffrent xsvf.

 

[daman10]

iv tried a couple, the console stays on till the first glitch attempt, it also works on stock image

turns out there only a couple of timing files and it just keeps glitching all rest red dot it?

 

[daman10]

I tried a thicker wire but still got the same results, im not planning on keeping this as a RGH console as i have a LTU2 board to go in it so only need the key

 

[daman10]

on the 0-2 timing file the console attempts to glitch but never boots xell

 

[alexander_1333]

You hear the fan slow down when the green light is on?

 

[daman10]

I think so although im not 100% as its next to my pc which has 6 fans roaring so a little hard to hear

 

[hersheys247]

Need to provide pic of ram chip for reference if glitchable with current hardware

 

[daman10]

It has Samsung ram, first thing I checked.

 

[gazcoigne]

you soldering leaves a lot to be desired clean it up remove the excess flux and trim the wires for the love of god!! what a messy install!!

also try the point FT3T10 for the cpu_rst (blue, D) wire works a lot better than the original point.

 

[daman10]

Although the soldering isnt perfect thats because its getting removed after i have the cpu key, there all making good connection.

 

[daman10]

Tried the alt point and still same result, the console stays on untill the debud light flashes for the first time then the red ring comes on

installed a different CR3 lite and its now attempting to glitch on all the timing files so hopefully ill b able to get xell

 

[islam.jamel]

corona v6 r1r1 remove it