CORONA Corona V6 wont boot into Xell - Please help

[vinavinay]

I am following steps below to boot into XELL. Please let me know if I am doing this correctly.

J-Runner Steps.
1. Read Nand twice, 46 MB file
2. Create ECC
3. Select RGH2, CR4 and Write ECC
4. Disconnect the console from PC, connect it to TV via AV cable
5. Plug power supply then press on power button from the front panel to start the console. Eject button do not start console, tried multiple times.
6. Console starts, green light blinks showing it glitches but XELL or Dash do not load.

Please tell me if I am doing everything correctly. If yes, please help me glitch my console.

 

[vinavinay]

I don't think that ECC or Xell file is getting written to my nand. Can someone please check the images above and let me know. I am pretty sure that it has nothing to do with soldering or CR4 installation. I think everything is perfect. I has to do something with the software part. There is something that I am missing but don't know what. If someone can check the hardware installation, everything and solve my issue , I will really be grateful to them.

 

[vinavinay]

Thank you for the reply, as instructed I have updated the J-Runnner to V0.3 Beta(7), created nand dump. However, I only have options glitch 2 and glitch2m. Out of this, I can select either glitch2 + CR4 or glitch2m. There is no option to select all 3 together. So I selected Glitch2+CR4, click on created ECC. JR immediately said ECC created. Then I wrote ECC, which finished immediately (this is the part which I think isn't happening correctly, can anyone let me know why? how to resolve this?).

Also, the resistance between C Pad and Grnd is 108.8 KOhms. Is it normal?

 

[vinavinay]

After struggling from past two days, I have come to a conclusion that I am unable to write XELL image to my nand using JRunner. That is why my system is not booting into XELL but can boot into stock I don't know the reason why? If anyone has a answer please help me out.

 

[briggs01]

After struggling from past two days, I have come to a conclusion that I am unable to write XELL image to my nand using JRunner. That is why my system is not booting into XELL but can boot into stock I don't know the reason why? If anyone has a answer please help me out.

when you see ECC created load that into source manually and write it , try that

click glitch2 and cr4

 

[stucknvegas]

Looks like you wrote the ECC fine Jrunner will show you a error message if it does not complete the write process

 

[vinavinay]

If my setup is good and JRunner is writing the ECC then why am I unable to start the console by pressing eject button.

 

[stucknvegas]

You say you can put retail back on the console does it start with the eject button when back to original ..Most of us use a wired controller or charge and play cable to start the XBOX ...I done hundreds of RGHs and never once used eject button to get XELL!!!! Most consoles you must complete one power cycle before the DVD eject will function on a slim So you have tried all combos of the dips *8-1 8-2 8-3 8-4 letting it cycle 2-3 minutes per setting Your soldering looks funny on the e pad of the CR-4 Some Your pictures are blurry Are you working on a super slim Emodel

 

[vinavinay]

There are two buttons on my console. One eject and one power button. On retail nand on pressing power button my console starts but not by pressing eject button. So goes after writing ECC. But after writing ECC and pressing power button, my console fan starts making bleeping/buzzing sound, green light blinks, blinks and after sometime fan rotates fast and console shut downs.

Does writing ECC, also writes XELL automatically to the console or is there something I need to do.

 

[stucknvegas]

So your console dings the bell when the RGH chip is enabled and you start your xbox what are you referencing ( beep sound ) ?
Yes the ECC is Xell

 

[stucknvegas]

So to confirm this with retail written to console and power cycle the xbox once with power button of face plate then no response or starting with DVD eject??
and yes your working on a EModel super slim
How are you disabling the CR-4 when starting with retail

 

[vinavinay]

Yes, I have XBOX 360 E console.
I will explain to you.
I reinstall Stock nand, the CR4 is still installed. Now I connect my console to my TV and press power button (not eject button), the console starts immediately to stock dash.
Then I try installing XELL (using write ECC), after this I connect my console to my TV again, and press eject button (this time), my console do not start. Then I press power button next to eject button and my console starts. The green light blinks, the fan makes noice and then nothing happens.

 

[Krafter]

So your console dings the bell when the RGH chip is enabled and you start your xbox what are you referencing ( beep sound ) ?
Yes the ECC is Xell

I think he is taking about the beeping fan noise that some Coronas make when glitching. I've been following this thread and if I understand it correctly, it's trying to glitch as the debug light is blinking.

Edit:

When I write ECC to nand and start the console, it makes buzzing/beep sound continuously with small intervals in between. The glitch light (green) blinks and after few blinking the fan speed increases and then console turns off itself.

.

 

[stucknvegas]

Thanks Krafter got it ...I done a lot of e models with no problems Just wondering if it is hardware or software
I wonder what will happen if he removes the 5 volt and Cpu-rst and tries to start with ECC written to machine

 

[Krafter]

Sounds like Xell is crashing to me. I haven't done any CR4 Corona installs so I can't really suggest anything.

 

[stucknvegas]

Can you download the CR-4 Majic files from the sticky post
tick the top load source in jrunner app
navigate to CORONA_4GB.ecc then tick write ECC button
http://team-xecuter.com/forums/showthread.php?147878-Xecuter-CR4-XL-Magic-SMC-Files-for-RGH2

 

[vinavinay]

"I think he is taking about the beeping fan noise that some Coronas make when glitching" - That is exactly what I'm talking about.

Thank you all for taking time and helping me with my situation.

There is a good news - "Hurray", I have glitched my XBOX, Finally. I am happy, happy, happy.

I used another laptop to run JRunner and write ECC. That's it, I was able to start my console in XEX using eject key. I got my CPU Key and DVD Key. Connected back my console to JRunner, created update.bin and flashed it.

Volla, my console started.

For this to happen, I played a lot with Dip Switches.

1. Initially started with dip 1-8, after 2-3 blinks, console turned off.
2. Dip 2-8, after 5-6 blinks, console turned off.
3. Skipped it, as it is 3-8 which wasn't working from start.
4. Dip 4-8, and to my surprise after 6 blinks, XEX loads. Here I am happy, happy, happy. Got the keys.
5. Tried Dip 5-8, with single blink, my console started loading. Happier than ever.

So, Jumper set to 10 KOHMs, Dips to 5-8, I get my system to boot with single blink and the fan nosie that I am talking about goes off as soon as console starts.

Installed XEX menu 12 from Dash. Now installing FreeStyle Dash..

Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you.........

 

[vinavinay]

I have another issue guys..

I have successfully copied XEX to internal 4 GB card and I am able to use it successfully.

I have formatted 16 GB pen drive and I am using it as a external disk for my console.

I tried installing FSD and Aurora, but I am unable to copy that to my 16 GB pen drive. Because XEX says it is full, but when I check it from stock dash, it says 14 GB available.

I would like to know, how can I install FSD, Aurora and dashlaunch to my 16 GB pendrive.

 

[stucknvegas]

I don't put any software on the 4 gig Internal !! You need a 2.5 sata Hard drive Aka laptop hard drive
You can find them cheap. Also you can purchase the plastic enclosure on E-bay. I use size 120- to 1 Terabyte
Just for the sake of learning what was the real problem with beep and fan changing speed
What does the console do if you return the dips 8-2 and cycle it. Please let us know
We are glad you got the console done your post was getting very long !!

 

[briggs01]

I have another issue guys..

I have successfully copied XEX to internal 4 GB card and I am able to use it successfully.

I have formatted 16 GB pen drive and I am using it as a external disk for my console.

I tried installing FSD and Aurora, but I am unable to copy that to my 16 GB pen drive. Because XEX says it is full, but when I check it from stock dash, it says 14 GB available.

I would like to know, how can I install FSD, Aurora and dashlaunch to my 16 GB pendrive.

to put freestyle onto you pen drive use a program called USB XTAF there are tuts online

http://www.google.co.uk/url?sa=t&rc...m0gcAF&usg=AFQjCNFUOyOSm_rM9yhvnqWclW9FNR_K5g