Not sure if this has been asked and answered before on this section but do the CR4's come all ready programmed straight out the box or do they still need programmed through J-Runner in the same way as previous version Coolrunners ?
ANSWERED CR4 for a Falcon
- Thread starter evertonman67
- Start date
have a good read through this I am sure if they needed programming it would have said , if you need help later on remember to take pics of soldering etc before posting , I say this because if you asking this now my guess is that you will asking questions laterhttp://team-xecuter.com/forums/showthread.php?147805-CR4-XL-PHAT-Zephyr-Opus-Falcon-Jasper-Install-Guide-(R-JTAG-)
Last edited:
Sweet indeed 
just that my mate has ordered the CR4 with the QSB's from Mod Supplier ( we're UK based and CK3 were sold out at the time he wanted to order )
So i'm just waiting for him to recieve his CR4 and QSB's and i'll be fitting this in his Falcon 360
just that my mate has ordered the CR4 with the QSB's from Mod Supplier ( we're UK based and CK3 were sold out at the time he wanted to order )So i'm just waiting for him to recieve his CR4 and QSB's and i'll be fitting this in his Falcon 360
sorry
http://team-xecuter.com/forums/show...phyr-Opus-Falcon-Jasper-Install-Guide-(R-JTAG-)
- - - Updated - - -
http://team-xecuter.com/forums/show...phyr-Opus-Falcon-Jasper-Install-Guide-(R-JTAG-)
- - - Updated - - -
Last edited:
I've done lots of Jtags in the past and a fair few phat RGH's using the Coolrunner 3 and Coolrunner 3 Lite in the past as well ( my own Falcon 360 is fitted with a CR3 Lite on RGH2 and boots within around 10-30 seconds )
But this will be my first ever fitting of the awsome CR4 and i'm confident enough that it should go smoothly i reckon
But like i asked,i wasn't sure if the CR4 was already pre-programmed straight out the box or not.
Thanks though for clearing up my query and i'll report back with an update and pics very soon
But this will be my first ever fitting of the awsome CR4 and i'm confident enough that it should go smoothly i reckon
But like i asked,i wasn't sure if the CR4 was already pre-programmed straight out the box or not.
Thanks though for clearing up my query and i'll report back with an update and pics very soon
Hi guys,
Just asking if i need to solder the R1 point on the JRP/Nand-X/CR QSB v3-Phat to the 2x small/tiny solder contacts near the HANA chip or do i leave it un-soldered ?
Oops,my stupidity lol,ignore that question ( as i checked over this QSB i realised it wasn't aligned properly.So i de-soldered the QSB completely and re-aligned it up to the exact point that R1 solders to
Just asking if i need to solder the R1 point on the JRP/Nand-X/CR QSB v3-Phat to the 2x small/tiny solder contacts near the HANA chip or do i leave it un-soldered ?
Oops,my stupidity lol,ignore that question ( as i checked over this QSB i realised it wasn't aligned properly.So i de-soldered the QSB completely and re-aligned it up to the exact point that R1 solders to
Last edited:
Guys,if i connect 1 & 3 pads on the JTAG ALT V2 QSB to use the AUD_CLAMP seetings,do i need any other bits of hardware at all ( only asking purely before i go ahead to R-Jtag+ this Falcon with the Coolrunner 4 ) ?
