- Dip switch settings : 3,8
- Postbit jumpers :0ohms
- Type of CPU_RST Cable Used : Supplied blue wire cut to length
- Any QSB jumper/switch settings : postfix Adapter v2
- Any caps installed: no
- Screenshots of RATER if used : N/A(console boots within 3 cycles)
- Was Console was booting before rgh attempt: yes
Hello..
Got a strange issue with 2 corona v3s i just did, both boot flawless with AV cord but will not boot with hdmi.
currently i have resorted to booting with AV plugged then swapping with hdmi when they boot.
I have tried the following,
1) Console Video Reset
2) Creating XeBuild image with nohdmi wait enabled
3) Procured new HDMI cord
4) Another TV
i am certain its an image issue because i tried the hdmi cords on a trinity and both cords/Television work perfectly.
------ Loading bootloaders and required security files ------
reading data\SMC.bin (0x3800 bytes)
reset smc load address to 0x800 size 0x3800
reading data\kv.bin failed, using kv.bin from nand dump
reading .\common\cba_13121.bin (0x1af0 bytes)
loaded cba_13121.bin, could not check signature rsa key not present!
reading .\common\cbb_13121.bin (0x7b40 bytes)
reading .\common\cd_12905.bin (0x5090 bytes)
reading .\common\ce_1888.bin (0x5606a b pad 0x56070 b)
reading data\xell-gggggg.bin (0x40000 bytes)
extracted SUPD\xboxupd.bin\CF_16747.bin (0x4560 bytes)
extracted SUPD\xboxupd.bin\CG_16747.bin (0x75aaa bytes)
reading 16747\bin\patches_g2corona.bin (0x8d8 bytes)
reading data\smc_config.bin failed, using smc_config.bin from nand dump
-------------------
checking smc_config
-------------------
extracting config
------------------
SMC config info:
------------------
Target temps: Cpu: 82øC Gpu: 78øC Edram: 76øC
Max temps : Cpu: 89øC Gpu: 82øC Edram: 82øC
Cpu Fan : (auto)
Gpu Fan : (auto)
MAC Address : 7c:1e:52:ca:80:87
AVRegion : 0x00000300 (PAL50)
GameRegion : 0x02fe (PAL/EU)
DVDRegion : 2
resetKey : YYDD
---------------------
Checking for smc config data patches
smc config was not patched
---------------------
could not check signature of cba_13121.bin, 1BL RSA key not present!
done!
patch slot offset reset to: 0xb0000
------ Patching BLs and modifying patches ------
Patching BLs...Done!
------ Patching boot reasons and options into flash header ------
Patching header for xell power reason
------ Encrypting and finalizing bootloaders ------
encoding SMC.bin size 0x3800
SMC checksum: fd7c6b42
unknown SMC found, type: Corona v6.2(2.05)
glitch hack found in SMC binary!
encoding kv.bin size 0x4000
decrypted keyvault has been set for reference
Master RSA pub not available, not checking hash
encoding cba_13121.bin size 0x1af0
encoding cbb_13121.bin size 0x7b40
CB 13121 seq 0x03020002 type: 0x03 cseq: 0x02 allow: 0x0002
expected fuses:
fuseset 00: C0FFFFFFFFFFFFFF
fuseset 01: 0F0F0F0F0F0FF0F0 (retail slim)
fuseset 02: 0F00000000000000 (sequence)
fuseset 02: 0F00000000000000 (allow cseq 2)
**dual CB flag detected!**
encoding cd_12905.bin size 0x5400
encoding ce_1888.bin size 0x56070
encoding xell-gggggg.bin size 0x40000
encoding cf_16747.bin size 0x4560
encoding cg_16747.bin size 0x75ab0
encoding patches_g2corona.bin size 0x4fc
done!
------ Adding bootloaders to flash image ------
adding SMC.bin at raw offset 0x00000800 len 0x3800 (end 0x4000)
adding kv.bin at raw offset 0x00004000 len 0x4000 (end 0x8000)
adding cba_13121.bin at raw offset 0x00008000 len 0x1af0 (end 0x9af0)
adding cbb_13121.bin at raw offset 0x00009af0 len 0x7b40 (end 0x11630)
adding cd_12905.bin at raw offset 0x00011630 len 0x5400 (end 0x16a30)
adding ce_1888.bin at raw offset 0x00016a30 len 0x56070 (end 0x6caa0)
adding xell-gggggg.bin at raw offset 0x00070000 len 0x40000 (end 0xb0000)
adding cf_16747.bin at raw offset 0x000b0000 len 0x4560 (end 0xb4560)
adding cg_16747.bin at raw offset 0x000b4560 len 0x75ab0 (end 0xc0000, rest in fs)
adding patches_g2corona.bin at raw offset 0x000c0010 len 0x4fc (end 0xc050c)
Fixing up FS table...done!
Writing zeropair CG patch slot overflow data to sysupdate.xexp1
at raw offset 0xd0000 len 0x0006a010 (end: 0x0013a010)...done!
------ adding 28 firmware files ------
extracted SUPD\aac.xexp (0x14000 bytes) (crc32: 0x12d353e9 ini: 0x12d353e9)
adding as aac.xexp1 at raw offset 0x13a010 len 0x00014000 (end 0x0014e010)
extracted SUPD\bootanim.xex (0x61000 bytes) (crc32: 0x151b0618 ini: 0x151b0618)
adding as bootanim.xex at raw offset 0x150000 len 0x00061000 (end 0x001b1000)
extracted SUPD\createprofile.xex (0xc000 bytes) (crc32: 0x32ceed5a ini: 0x32ceed5a)
adding as createprofile.xex at raw offset 0x1b1000 len 0x0000c000 (end 0x001bd000)
extracted SUPD\dash.xex (0x598000 bytes) (crc32: 0x4103a319 ini: 0x4103a319)
adding as dash.xex at raw offset 0x1c0000 len 0x00598000 (end 0x00758000)
extracted SUPD\deviceselector.xex (0xa000 bytes) (crc32: 0xfe497738 ini: 0xfe497738)
adding as deviceselector.xex at raw offset 0x758000 len 0x0000a000 (end 0x00762000)
extracted SUPD\gamerprofile.xex (0x1b000 bytes) (crc32: 0xef9022d5 ini: 0xef9022d5)
adding as gamerprofile.xex at raw offset 0x762000 len 0x0001b000 (end 0x0077d000)
extracted SUPD\hud.xex (0x1d000 bytes) (crc32: 0xc0e76e31 ini: 0xc0e76e31)
adding as hud.xex at raw offset 0x77f000 len 0x0001d000 (end 0x0079c000)
extracted SUPD\huduiskin.xex (0x14000 bytes) (crc32: 0x155495d3 ini: 0x155495d3)
adding as huduiskin.xex at raw offset 0x79d000 len 0x00014000 (end 0x007b1000)
extracted SUPD\mfgbootlauncher.xex (0x8000 bytes) (crc32: 0xdecbab8e ini: 0xdecbab8e)
adding as mfgbootlauncher.xex at raw offset 0x7b4000 len 0x00008000 (end 0x007bc000)
extracted SUPD\minimediaplayer.xex (0xc000 bytes) (crc32: 0x2892b8d5 ini: 0x2892b8d5)
adding as minimediaplayer.xex at raw offset 0x7bc000 len 0x0000c000 (end 0x007c8000)
extracted SUPD\nomni.xexp (0xc800 bytes) (crc32: 0xdcef767a ini: 0xdcef767a)
adding as nomni.xexp1 at raw offset 0x7c8000 len 0x0000c800 (end 0x007d4800)
extracted SUPD\nomnifwk.xexp (0x2000 bytes) (crc32: 0x0d14c998 ini: 0x0d14c998)
adding as nomnifwk.xexp1 at raw offset 0x7d4800 len 0x00002000 (end 0x007d6800)
extracted SUPD\nomnifwm.xexp (0x5000 bytes) (crc32: 0xdc46bb6e ini: 0xdc46bb6e)
adding as nomnifwm.xexp1 at raw offset 0x7da000 len 0x00005000 (end 0x007df000)
extracted SUPD\SegoeXbox-Light.xtt (0x6000 bytes) (crc32: 0xe0ee6049 ini: 0xe0ee6049)
adding as SegoeXbox-Light.xtt at raw offset 0x7e1000 len 0x00006000 (end 0x007e7000)
extracted SUPD\signin.xex (0x19000 bytes) (crc32: 0xcbfce61f ini: 0xcbfce61f)
adding as signin.xex at raw offset 0x7ea000 len 0x00019000 (end 0x00803000)
extracted SUPD\updater.xex (0x7000 bytes) (crc32: 0xafef5cf0 ini: 0xafef5cf0)
adding as updater.xex at raw offset 0x805000 len 0x00007000 (end 0x0080c000)
extracted SUPD\vk.xex (0xb000 bytes) (crc32: 0xf2caff49 ini: 0xf2caff49)
adding as vk.xex at raw offset 0x80f000 len 0x0000b000 (end 0x0081a000)
extracted SUPD\xam.xex (0x253000 bytes) (crc32: 0x79f6eabf ini: 0x79f6eabf)
adding as xam.xex at raw offset 0x81b000 len 0x00253000 (end 0x00a6e000)
extracted nanddump\xenonclatin.xtt (0x11b000 bytes) (crc32: 0xd5d17ff5 ini: 0xd5d17ff5)
adding as xenonclatin.xtt at raw offset 0xa6f000 len 0x0011b000 (end 0x00b8a000)
extracted SUPD\xenonclatin.xttp (0x18000 bytes) (crc32: 0x7a507ad1 ini: 0x7a507ad1)
adding as xenonclatin.xttp1 at raw offset 0xb8b000 len 0x00018000 (end 0x00ba3000)
extracted nanddump\xenonjklatin.xtt (0x1a8000 bytes) (crc32: 0xdde4a14c ini: 0xdde4a14c)
adding as xenonjklatin.xtt at raw offset 0xba4000 len 0x001a8000 (end 0x00d4c000)
extracted SUPD\xenonjklatin.xttp (0x7000 bytes) (crc32: 0xe2adddfb ini: 0xe2adddfb)
adding as xenonjklatin.xttp1 at raw offset 0xd4c000 len 0x00007000 (end 0x00d53000)
extracted SUPD\ximecore.xex (0x17000 bytes) (crc32: 0x4c2f6bd1 ini: 0x4c2f6bd1)
adding as ximecore.xex at raw offset 0xd53000 len 0x00017000 (end 0x00d6a000)
extracted nanddump\ximedic.xex (0x90000 bytes) (crc32: 0x1d992bfb ini: 0x1d992bfb)
adding as ximedic.xex at raw offset 0xd6b000 len 0x00090000 (end 0x00dfb000)
extracted SUPD\ximedic.xexp (0x2800 bytes) (crc32: 0x34c9b084 ini: 0x34c9b084)
adding as ximedic.xexp1 at raw offset 0xdfc000 len 0x00002800 (end 0x00dfe800)
reading 16747\..\launch.xex (0xd000 bytes)
adding as launch.xex at raw offset 0xdfe800 len 0x0000d000 (end 0x00e0b800)
reading 16747\..\lhelper.xex (0x6000 bytes)
adding as lhelper.xex at raw offset 0xe0d000 len 0x00006000 (end 0x00e13000)
reading 16747\..\launch.ini (0x1c4 bytes)
adding as launch.ini at raw offset 0xe16000 len 0x000001c4 (end 0x00e161c4)
------ adding 5 security files ------
<- Processing crl.bin ->
reading data\crl.bin (0xa00 bytes)
crl appears crypted, attempting to decrypt with CPU key...failed! Trying alternate key...success!
adding as crl.bin at raw offset 0xe1c000 len 0x00000a00 (end 0x00e1ca00)
<- Processing dae.bin ->
reading data\dae.bin (0xad30 bytes)
dae appears encrypted, attempting to decrypt with CPU key...failed! Attempting to decrypt with alternate key...
success!
adding as dae.bin at raw offset 0xe20000 len 0x0000ad30 (end 0x00e2ad30)
<- Processing extended.bin ->
reading data\extended.bin (0x4000 bytes)
adding as extended.bin at raw offset 0xe2c000 len 0x00004000 (end 0x00e30000)
<- Processing fcrt.bin ->
could not read fcrt.bin, using data from previous parse...
adding as fcrt.bin at raw offset 0xe30000 len 0x00004000 (end 0x00e34000)
<- Processing secdata.bin ->
reading data\secdata.bin (0x400 bytes)
adding as secdata.bin at raw offset 0xe34000 len 0x00000400 (end 0x00e34400)
------ checking for Mobile*.dat ------
MobileB.dat found, adding from previous parse
adding MobileB.dat as type 0x31 at raw offset 0xe38000 len 0x800 (end 0xe38800)
MobileC.dat found, adding from previous parse
adding MobileC.dat as type 0x32 at raw offset 0xe3c000 len 0x200 (end 0xe3c200)
MobileD.dat found, adding from previous parse
adding MobileD.dat as type 0x33 at raw offset 0xe40000 len 0x800 (end 0xe40800)
MobileE.dat found, adding from previous parse
adding MobileE.dat as type 0x34 at raw offset 0xe44000 len 0x800 (end 0xe44800)
Statistics.settings found, adding from previous parse
adding Statistics.settings at raw offset 0xf78000 len 0x1000 (end 0xf79000)
Manufacturing.data found, adding from previous parse
adding Manufacturing.data at raw offset 0xf74000 len 0x1000 (end 0xf75000)
------ adding smc_config.bin ------
adding smc config to offset 0x00f7c000, len 0x400
------ finalizing image ------
Fixing up empty FS block entries...done!
Writing FS table to image offset 0xe48000 len 0x4000 (end 0xe4c000)...done!
fixing up big block controller on small block NAND LBA numbers...done!
calculating ECD bytes and assembling raw image...done!
remapping 1 blocks
copying 0x4200 bytes of LBA 0x64 to block 0x3ff...zero fill origin...done!
done remapping!
------ writing image to disk ------
writing file 'C:\Users\User\Desktop\J-Runner (16756)\J-Runner\100173223143\updflash.bin' to disk...done!
---------------------------------------------------------------
C:\Users\User\Desktop\J-Runner (16756)\J-Runner\100173223143\updflash.bin image built, info:
---------------------------------------------------------------
Kernel : 2.0.16747.0
Console : Corona
NAND size : 16MiB
Build : Glitch (v2)
Xell : power on console with console eject button
Serial : 100173223143
ConsoleId : 406644655437
MoboSerial: 7501135203132315
Mfg Date : 07/31/2012
CPU Key : D5FDCB9Dxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx6
1BL Key : DD88AxxxxxxxxxxxxxxxxxxxxxxxxxxxB68563EFA
DVD Key : 20EABF08362826FCEC08068F9B5CED91
CF LDV : 2
KV type : type2 (hashed - unchecked, master key not available)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
HTML:
