CR4 XL NO GREEN LIGHT i need help

[cubano123]

i cant get my cr4 green light to come on.
please help me

I read my nand with nand x and selected teh rgh ecc file for corona 16 mb adb then clicked write ecc to nand. Then i attempted to boot up console with av cable in back of tv and eterhent cable from router to xbox trying to boot xell but no green light on cr4

 

[BL4K3Y]

Those images are too small.

Upload them separately and add them to your post please.

 

[cubano123]

i took them with my cell phone and when i try iupload it it says failed. is there a site i can host the images?

 

[BL4K3Y]

i took them with my cell phone and when i try iupload it it says failed. is there a site i can host the images?

I use TinyPic to upload photos.

 

[cubano123]

ok here they are

http://postimg.org/image/xv27ydzer/
http://postimg.org/image/h2oty7ctr/
http://s15.postimg.org/sen6lblor/20141128_202630.jpg

http://postimg.org/image/jkrgmyd3h/
http://postimg.org/image/cjn5qitld/
http://postimg.org/image/j1cjarhvf/
http://postimg.org/image/qyus31lyt/

 

[BL4K3Y]

Make your blue and yellow wires as short as possible and lay your wires flat before you solder them.

Have you got dip switches 3 and 8 ON with the rest OFF?

 

[cubano123]

Yes dip 3 and 8 are one and others are off.
Do you want me to resolder all my wires from my cr4 with the
wires laying down?

 

[BL4K3Y]

Do you want me to resolder all my wires from my cr4 with the
wires laying down?

Yes and cut the blue and yellow wires to fit.

They should be as short as you can make them.

 

[cubano123]

Ok im gonna do that rite now... stay close by... ill be back in 2 minutes

 

[cubano123]

still no green light. Im working on a corona v3. only red light is on

 

[keil423]

I'm going to bet that your problem is with your post fix adapter. It's really easy to bend the pin on those if your not careful. Get us a pic of that area please as it makes the most sense for your problem.

 

[Sasuke Uchiha]

also make sure the post out pin actually went in sometimes it gets stuck on the xcgpu and dosnt go under but looks like it did.

 

[Antalpromille]

I'm going to bet that your problem is with your post fix adapter. It's really easy to bend the pin on those if your not careful. Get us a pic of that area please as it makes the most sense for your problem.

Or just desolder the wire and measure the post pads against GND.

 

[cubano123]

Ok i will take a pic... I used the same post fix adapter wen wiring up ny dgx to it and got a green debug light... will that rule out the fact that installed the postfix adapter rite?

This is the pic
http://i57.tinypic.com/99gtjc.jpg

 

[cubano123]

any ideas anyone

 

[Antalpromille]

any ideas anyone

yes, desolder the wire and measure the post pad resistance agains GND as i said.

 

[The Result]

Why do you have soooo much exposed wire? Seriously if that was more heavy duty wire I probably could use it as a rope. I would try trimming all your wires shorter and lay them flat to the console when installing them.

 

[gizmo613]

i think the problem is the ipex connector, looks like he soldered it.

 

[Antalpromille]

i think the problem is the ipex connector, looks like he soldered it.

It does look that, didnt see that.

 

[cubano123]

what is the ipex connector?