Hi guys,
Need a bit of help with my demon. I was given a demon from a friend as he had trouble getting it installed and working.
I posted a thread asking if it might be faulty http://www.team-xecuter.com/forums/showthread.php?t=91873
I cleaned up the demon and proceeded to install it into a jasper, once installed i couldnt get the xbox to power on so i got my meter out and found a short between D4 and D5 on the demon qsb. So i corrected the short and the xbox turned on however i encounted another problem... i couldnt write to the demon "unkown nand flash device" in demon tool box.
I contacted my friend and asked him what problems he had with it and he too got "unkown nand flash device" in demon tool box.
I could get it to write to the demon in j runner but j runner would crash on me?????
So i decided to carefully remove the demon from my jasper and checked its read/write functionality with a micro usb cable and it works fine.
I was stumped but decided to give it another try but this time doing a wire install as i thought the quick solder points might be dodgy. After the wire install and to my surprise it worked!!!!! I could read/write to both nands no problem! SORTED!
I started to try different timing settings as my jasper was a bit stubborn with rgh2, im using a CPU reset cleaner to help with the glitch times. Then out of nowhere the fans sped up, the light on the CR wasnt blinking??? I switched it back to stock nand and again the fans would just speed it, no boot????
I then flashed my original nandump back to xbox nand with demon toolbox and then the glitch image to demon but still no success. Just before i had given up i used jrunner to flash both nands and BOOM!!!... booted both nands no problem! I then plugged in my 160gb hdd and formatted it ready for insatlling FSD but it was very late by now so i decided to get some sleep and then finish it off in the morning.
Morning comes and with a cup of coffee in one had and xex.menu in the other i go to turn on my jasper and the fans just sped up and no boot on both nands! WTF! F******G PIECE OF MS CRAP!
Weirdly, sometimes, when booting the glitch nand the fans would speed up for about 5-10 seconds then slow down to normal, then the CR light will flash and then it would boot?
Any ideas on this guys as im now a bald man after pulling all my hair out!
Ive checked with my multi-meter from pins on the nand to the demon for continuity and shorts and its all fine.
Im sorry i used one colour wire for wire install but thats all i had.
Let me know your thoughts guys.
Thanks
J
Need a bit of help with my demon. I was given a demon from a friend as he had trouble getting it installed and working.
I posted a thread asking if it might be faulty http://www.team-xecuter.com/forums/showthread.php?t=91873
I cleaned up the demon and proceeded to install it into a jasper, once installed i couldnt get the xbox to power on so i got my meter out and found a short between D4 and D5 on the demon qsb. So i corrected the short and the xbox turned on however i encounted another problem... i couldnt write to the demon "unkown nand flash device" in demon tool box.
I contacted my friend and asked him what problems he had with it and he too got "unkown nand flash device" in demon tool box.
I could get it to write to the demon in j runner but j runner would crash on me?????
So i decided to carefully remove the demon from my jasper and checked its read/write functionality with a micro usb cable and it works fine.
I was stumped but decided to give it another try but this time doing a wire install as i thought the quick solder points might be dodgy. After the wire install and to my surprise it worked!!!!! I could read/write to both nands no problem! SORTED!
I started to try different timing settings as my jasper was a bit stubborn with rgh2, im using a CPU reset cleaner to help with the glitch times. Then out of nowhere the fans sped up, the light on the CR wasnt blinking??? I switched it back to stock nand and again the fans would just speed it, no boot????
I then flashed my original nandump back to xbox nand with demon toolbox and then the glitch image to demon but still no success. Just before i had given up i used jrunner to flash both nands and BOOM!!!... booted both nands no problem! I then plugged in my 160gb hdd and formatted it ready for insatlling FSD but it was very late by now so i decided to get some sleep and then finish it off in the morning.
Morning comes and with a cup of coffee in one had and xex.menu in the other i go to turn on my jasper and the fans just sped up and no boot on both nands! WTF! F******G PIECE OF MS CRAP!
Weirdly, sometimes, when booting the glitch nand the fans would speed up for about 5-10 seconds then slow down to normal, then the CR light will flash and then it would boot?
Any ideas on this guys as im now a bald man after pulling all my hair out!
Ive checked with my multi-meter from pins on the nand to the demon for continuity and shorts and its all fine.
Im sorry i used one colour wire for wire install but thats all i had.
Let me know your thoughts guys.
Thanks
J
